CALEX 4301004300
CALEX Falerna Wall Lamp Instruction Manual
Model: 4301004300
Introduction
Thank you for choosing the CALEX Falerna Wall Lamp. This manual provides essential information for the safe and efficient use of your new wall lamp. The Falerna lamp features a sleek design with warm white up & down lighting, a rechargeable battery, wireless operation, dimming capabilities, and an integrated motion sensor. It is suitable for both indoor and outdoor use due to its IP44 waterproof rating.
Package Contents
- 2x CALEX Falerna Wall Lamps
- 1x Remote Control
- 2x USB-C Charging Cables (1.5m each)
- Mounting Materials (magnetic mounting plates, screws, wall plugs)
Safety Information
- Always handle the lamp with care.
- Do not attempt to open or modify the lamp, as this will void the warranty and may cause damage or injury.
- Keep the lamp away from extreme temperatures and direct sunlight during charging to prevent overheating.
- Use only the provided USB-C cable for charging.
- Ensure the mounting surface is stable and can support the weight of the lamp.
- Dispose of batteries and electronic waste according to local regulations.
Setup and Installation
The CALEX Falerna Wall Lamp is designed for quick and easy installation without the need for complex wiring. It features a magnetic mounting system.
1. Charging the Lamp
Before first use, fully charge the lamp. Connect the provided USB-C cable to the charging port on the lamp and to a suitable USB power adapter (not included). A full charge takes approximately 6 hours and provides up to 8 hours of illumination.
2. Mounting the Lamp
- Choose a desired location for the lamp. Ensure the surface is clean and dry.
- Attach the magnetic mounting plate to the wall using the provided screws and wall plugs. For outdoor use, ensure the mounting is secure and weather-resistant.
- Align the lamp with the mounted plate. The lamp will magnetically attach to the plate. This allows for easy removal for charging or repositioning.

Image: Installation of the Calex Falerna wall lamp using the magnetic mounting plate.

Image: The Calex Falerna wall lamp showing its integrated control buttons.
Operating Instructions
The Falerna wall lamp can be operated using the integrated buttons or the included remote control.
Using the Remote Control

Image: Operating the Calex Falerna wall lamps with the remote control.
- ON/OFF: Press to turn the lamp on or off.
- MODE: Cycles through different lighting modes (if available).
- '+' / '-': Adjust the brightness (dimming function).
- TIMER 1H / TIMER 2H: Set the lamp to turn off automatically after 1 or 2 hours.
Motion Sensor Functionality
The integrated motion sensor detects movement within a range of 2-5 meters and a detection angle of 90°. When motion is detected, the lamp will automatically illuminate and remain on for 30 seconds before turning off. This feature is ideal for security lighting at entrances or in gardens.
Note: The motion sensor activates when the lamp is in an active state (not completely off). If the lamp is off, it will not react to motion. Ensure the lamp is switched on for the motion sensor to function.
Maintenance
The CALEX Falerna Wall Lamp requires minimal maintenance.
- Cleaning: Wipe the lamp with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Battery Care: Recharge the lamp regularly to maintain battery health, especially if it will not be used for extended periods.
- Weather Resistance: The IP44 rating ensures the lamp is protected against splashing water from any direction. While suitable for outdoor use, avoid submerging the lamp in water.

Image: The Calex Falerna wall lamp demonstrating its IP44 waterproof rating.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | Battery is depleted. Lamp is switched off. | Charge the lamp fully using the USB-C cable. Ensure the lamp is switched on via the remote or integrated button. |
| Motion sensor not activating. | Lamp is off. Obstruction in sensor's field of view. Sensor range exceeded. | Ensure the lamp is switched on. Clear any obstructions. Move closer to the lamp (within 2-5 meters). |
| Lamp does not hold charge. | Battery degradation. Improper charging. | Ensure the USB-C cable and power adapter are functioning correctly. If the issue persists after proper charging, contact customer support. |
| Remote control not working. | Remote battery depleted. Obstruction between remote and lamp. | Replace the remote control battery. Ensure a clear line of sight to the lamp. |
Specifications
| Model Number | 4301004300 |
| Brand | CALEX |
| Dimensions (L x W x H) | 8 x 8 x 8 cm |
| Weight | 725 g |
| Material | Aluminium |
| Color | Black |
| Light Source | LED |
| Light Color | Warm White (2700K) |
| Brightness | 150 Lumen (Max) |
| Wattage | 10 Watt |
| Voltage | 3.7 Volt |
| Power Source | Rechargeable Battery (2000mAh) |
| Charging Time | Approx. 6 hours |
| Operating Time | Up to 8 hours |
| Water Resistance Level | IP44 (Water-resistant) |
| Special Features | Motion Sensor, Dimmable, Wireless, Remote Control |
| Motion Sensor Range | 2-5 meters |
| Motion Sensor Angle | 90° |
| Mounting Type | Wall Mount (Magnetic) |

Image: Dimensions of the Calex Falerna wall lamp.

Image: Energy efficiency label for the Calex Falerna lamp. For more details, visit the EPREL database.
Warranty and Support
Specific warranty details are not provided in this manual. Please refer to your purchase documentation or contact the retailer/manufacturer directly for warranty information and customer support. For general inquiries or technical assistance, please visit the official CALEX website or contact their customer service department.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.



