Gettimore L88U6JTQ0H8785BZ764FP4P

Download PDF
Contents

Gettimore Compatible Dryer Filter Set for Miele Heat Pump and Condenser Dryers

Instruction Manual

1. Introduction

This instruction manual provides essential information for the proper installation, maintenance, and use of your Gettimore compatible dryer filter set. These filters are designed to replace original Miele filters 6057930 and 9688381, ensuring your Miele heat pump or condenser dryer operates efficiently.

2. Product Compatibility

The Gettimore filter set is compatible with a wide range of Miele heat pump and condenser dryer models. Regular replacement of these filters is crucial for maintaining optimal dryer performance and energy efficiency.

Compatible Miele Dryer Models (Partial List):

  • T 8000 Supertronic Series
  • T 9747 WP, T 9767 WP
  • T 8627 WP, T 8926 WP, T 8927 WP, T 8966 WP
  • TKR350, TKR400-50, TKR450WP, TKR600-50, TKR650WP, TKR800-50, TKR850WP
  • TKS300-50, TKS350WP, TKS600-50, TKS650WP, TKS800-50, TKS850WP
  • TMB100-40, TMB140WP, TMB300-40, TMB340WP, TMB540WP, TMB600-40, TMB640WP
  • TMC547WP, TMC640WP, TMG400-40, TMG440WP
  • And other models replacing Miele filter numbers 6057930 and 9688381.

3. Package Contents

Your Gettimore compatible dryer filter set includes:

  • 3 x Large Foam Filters (approx. 282 x 196 x 4 mm)
  • 6 x Small Foam Filters (approx. 225 x 45 x 5 mm)
Three large rectangular foam filters and six smaller rectangular foam filters, all black.

Image 1: Contents of the Gettimore compatible dryer filter set, showing three large and six small foam filters.

Diagram illustrating the two types of filters: three larger, arrow-shaped filters and six smaller, rectangular filters.

Image 2: Visual representation of the filter types and quantities included in the package.

4. Setup and Installation

Follow these general steps to replace the filters in your Miele dryer. Refer to your specific Miele dryer's user manual for exact filter compartment locations and removal procedures.

  1. Power Off: Always disconnect your dryer from the power supply before performing any maintenance or installation.
  2. Locate Filter Compartment: The filter compartments are typically located at the front bottom of the dryer, often behind a removable panel or flap.
  3. Remove Old Filters: Carefully remove the used large and small foam filters from their respective slots. Note their orientation for correct installation of the new filters.
  4. Clean Compartment (Optional but Recommended): Gently clean any lint or debris from the filter compartments before inserting new filters.
  5. Insert New Filters: Place the new Gettimore large and small foam filters into their designated slots, ensuring they fit snugly and are correctly oriented. The dimensions of the large filters are approximately 282 x 196 x 4 mm, and the small filters are approximately 225 x 45 x 5 mm.
  6. Secure Compartment: Close the filter compartment panel or flap securely.
  7. Restore Power: Reconnect your dryer to the power supply.

5. Operating Considerations

These filters are passive components designed to capture lint and debris. Their proper function is ensured by correct installation and regular replacement. No specific operating steps are required for the filters themselves beyond ensuring they are correctly installed before each drying cycle.

6. Maintenance

The primary maintenance for these filters is timely replacement. While some Miele filters are washable, these Gettimore compatible foam filters are designed for replacement to maintain optimal filtration and dryer efficiency.

  • Regular Replacement: Replace your dryer filters regularly according to your dryer's recommendations or when you notice a decrease in drying performance or an increase in drying time.
  • Inspection: Periodically inspect the filters for signs of wear, damage, or excessive accumulation of lint that cannot be easily removed.
Close-up view of the black foam filter material, showing its porous texture.

Image 3: Close-up of the foam filter material, highlighting its texture for effective lint capture.

7. Troubleshooting

If you experience issues with your dryer after filter replacement, consider the following:

  • Incorrect Installation: Ensure all filters are correctly seated in their compartments and that the compartment door is fully closed. An improperly seated filter can affect airflow.
  • Filter Type: Verify that you are using the correct Gettimore compatible filters for your specific Miele dryer model, replacing Miele part numbers 6057930 and 9688381.
  • Other Dryer Issues: If filter replacement does not resolve performance issues, the problem may lie with another component of the dryer. Consult your Miele dryer's user manual or a qualified technician.

8. Specifications

AttributeDetail
BrandGettimore
Model Number (Product)L88U6JTQ0H8785BZ764FP4P
Replaces Miele Part Numbers6057930, 9688381
Large Filter Dimensions (approx.)282 x 196 x 4 mm
Small Filter Dimensions (approx.)225 x 45 x 5 mm
MaterialFoam
Package Quantity3 sets (3 large filters, 6 small filters total)

9. Warranty Information

Warranty information for this product is not available in the provided documentation. Please refer to the product packaging or contact the retailer or manufacturer directly for details regarding warranty coverage.

10. Support

For further assistance or inquiries regarding Gettimore compatible dryer filters, please contact the manufacturer or your point of purchase. Ensure you have your product model number (L88U6JTQ0H8785BZ764FP4P) available when seeking support.

© 2025 Gettimore. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.