Introduction
The Evenflo Revolve360 Slim 2-in-1 Rotational Car Seat is designed for child safety and ease of use in vehicles. This car seat offers two modes of use: rear-facing and forward-facing, accommodating children from 4 lb to 65 lb. Its rotational feature simplifies placing and removing your child from the vehicle. This manual provides essential information for the correct installation, operation, and maintenance of your car seat.
Safety Information
This car seat meets or exceeds all applicable federal safety standards. It has undergone structural integrity testing at energy levels approximately twice the federal crash test standard, and is side-impact tested, rollover tested, and temperature tested. Always ensure the car seat is correctly installed and your child is properly secured in the harness system before every trip. Refer to the indicators on the car seat base to confirm correct installation and seat positioning.
Image: The L.I.F.E. Guard feature is designed to improve safety performance during side impact crashes.
Setup and Installation
The Revolve360 Slim features the Sure360™ Safety Installation System with LockStrong™ and Tether360™ for secure and simple installation. A bead-level indicator assists in achieving the correct leveling.
Installation Steps:
- Prepare the Vehicle Seat: Ensure the vehicle seat is clear of obstructions.
- Position the Base: Place the car seat base firmly on the vehicle seat.
- Secure with LATCH or Seatbelt:
- LATCH System: Locate the lower anchor attachments on the car seat base and connect them to your vehicle's lower anchors. Tighten until the base is secure.
- Vehicle Seatbelt: Route the vehicle's lap and shoulder belt through the designated belt path on the car seat base. Engage the LockStrong™ arm to secure the belt.
- Check Leveling: Use the bead-level indicator on the base to ensure the car seat is at the correct angle for your child's weight and height.
- Attach the Car Seat: Place the car seat onto the installed base. Ensure it clicks securely into place. The green indicator will confirm it is locked.
Image: The Sure360 Safety Installation System ensures a secure fit in your vehicle.
Image: Detail of the LATCH/UAS belt path and storage for secure installation.
Image: The Belt Lock indicator on the base shows green when the seat is securely locked.
Operating Instructions
360° Rotation:
The car seat features a one-hand, 360° rotation mechanism. To rotate the seat, lift the lever located at the top of the seat and gently turn the car seat to the desired position (rear-facing or forward-facing). Ensure the seat locks into place before securing your child.
Image: The car seat rotates 360 degrees for easy access to your child.
Harness Adjustment:
Adjust the harness straps to fit snugly against your child's shoulders. The harness height can be adjusted without rethreading. Ensure the chest clip is positioned at armpit level.
Recline Positions:
The car seat offers 6 reclining positions. Adjust the recline to the perfect angle for your child without needing to reinstall the car seat.
Maintenance
Quick Clean Cover:
The Quick Clean Cover is designed for easy removal and washing. To clean, machine wash the seat pad separately in cold water on a delicate cycle. Tumble dry for 10 to 15 minutes on low heat. Do not lubricate or immerse in water any part of this child restraint, unless rinsing is permitted. Plastic and metal parts may be wiped clean with mild soap and water and dried with a soft cloth. The harness can be wiped clean with mild soap and water; allow harness to air dry.
Image: The Quick Clean Cover can be easily unzipped for removal and washing.
Troubleshooting
- Car Seat Not Rotating: Ensure the car seat is not fully reclined or obstructed. Lift the rotation lever completely before attempting to turn the seat.
- Harness Too Tight/Loose: Check the harness adjuster strap located at the front of the seat. Ensure the harness is snug enough that you cannot pinch any excess webbing at the child's collarbone.
- Difficulty Installing: Verify that the LATCH connectors or vehicle seatbelt are routed correctly through the designated paths. Apply firm pressure to the car seat while tightening to remove slack. Consult the bead-level indicator for proper angle.
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 21 x 24.3 x 16.75 inches |
| Item Weight | 28.2 pounds |
| Material Type | 100% Polyester |
| Rear-facing Child Weight | 4 lb to 50 lb |
| Rear-facing Child Height | 17 in. to 48 in. |
| Forward-facing Child Weight | 22 lb to 65 lb |
| Forward-facing Child Height | 28 in. to 49 in. |
| Number of Reclining Positions | 6 |
| Harness Type | 5-Point |
Image: The car seat supports extended rear-facing from 4 to 50 lbs and forward-facing from 22 to 65 lbs.
Image: The 16.7-inch width of the car seat is designed to maximize space in your backseat.
Warranty and Support
Evenflo car seats are designed to meet or exceed government safety standards. For assistance with installation or any product-related inquiries, Evenflo offers ParentLink® customer service. Live video support with a certified car seat safety technician is available to assist with proper vehicle installation, ensuring you can drive with confidence.
For detailed warranty information, please refer to the warranty card included with your product or visit the official Evenflo website.
