SEGMART HT01 4-6 Person Inflatable Hot Tub User Manual

1. Important Safety Information

Please read and understand all instructions before installing and using this product. Failure to follow these instructions could result in serious injury or death.

• Always supervise children.
• Do not use the hot tub if the water temperature exceeds 104°F (40°C).
• Consult a doctor before use if pregnant, diabetic, in poor health, or under medical care.
• Do not use electrical appliances near the hot tub.
• Ensure the hot tub is placed on a flat, stable surface capable of supporting its full weight when filled.
• California Sales Restrictions: Due to specific regulations, this product is not available for sale in California.

2. Product Overview

Key Features:

• Bubble Massage System: Equipped with 130 high-powered air jets driven by a 600W motor for a full-body massage.
• Smart Heating & Energy-Efficient Design: Maintains water temperature efficiently up to 104°F (40°C) with an insulated cover and child-safety lock.
• Durable & Portable Design: Constructed from reinforced laminated PVC for superior puncture resistance. Includes a carry bag for easy transport.
• Complete Accessories: Includes electric pump, 6 high-flow filters, inflatable lid, repair kit, non-slip floor mat, and storage bag.
• Intuitive Controls: Features a built-in digital control panel for easy temperature and bubble jet adjustment.

Specifications:

3. Setup Instructions

3.1 Site Preparation

Choose a flat, level surface free from sharp objects. Ensure the chosen location can support the weight of the filled hot tub (approximately 2000 lbs for 240 gallons of water plus occupants).

• Unfold the ground mat and place it on the chosen surface.
• Carefully unroll the hot tub onto the center of the ground mat.
• Verify the drainage valve at the bottom of the tub is fully sealed.

Figure 3.1: The SEGMART Inflatable Hot Tub in use, demonstrating its size and appearance.

3.2 Inflation Procedure

Use the provided electric pump to inflate the hot tub. Do not overinflate; the tub should feel firm but not rigid.

• Attach the inflation hose from the electric pump to the tub's air valve.
• Ensure the heater pump's front base panel is securely closed.
• Power on the pump and activate inflation mode by pressing the BUBBLE button.
• Inflate until structural rigidity is achieved (do not exceed recommended pressure).
• Terminate inflation by pressing BUBBLE again, then engage the LOCK function to deactivate the system.
• Inflate the lid separately using the same pump and hose.

Figure 3.2: Key components for setup and operation, including the inflation valve and control panel.

3.3 Connecting the Control Panel and Filter System

Connect the heater pump to the tub and install the filter cartridges.

• Unscrew the front bottom cover of the pump to expose the connection ports.
• Connect the heating pump to the tub by installing the three supplied hoses to the corresponding ports. Ensure all connections are tight.
• Secure the filter cover onto a filter cartridge, then insert the assembled cartridge into the tub's water inlet.

Figure 3.3: Diagram illustrating the hot tub's specifications including number of jets, filtration rate, max temperature, power cord length, heating power, and wave-making power.

3.4 Filling the Tub

Fill the hot tub with water using a garden hose. For faster heating, use warm water if available.

• Fill the tub to a level between the MIN and MAX markers indicated on the inner wall.
• Ensure water pressure is adequate for filling.

Figure 3.4: The hot tub filled and ready for use, showing its spacious interior.

Setup Video Guide:

4. Operating Instructions

4.1 Digital Control Panel

The hot tub features an intuitive digital control panel to manage all functions.

• Temperature Adjustment: Use the up/down arrows to set your desired water temperature (range typically 68°F to 104°F / 20°C to 40°C).
• Heater Button: Press to activate the heating function. The heater indicator light will illuminate.
• Bubble Button: Press to activate the 130 air jets for a relaxing massage. Press again to turn off.
• Filter Button: Activates the filtration system to circulate and clean the water.

Figure 4.1: The digital control panel for easy operation of temperature and bubble jets.

4.2 Heating the Water

After filling the tub, set your desired temperature and activate the heater.

• Set the desired temperature using the digital control panel.
• Press the HEATER button. The water will begin to heat.
• Cover the hot tub with the insulated lid to retain heat and reduce heating time. Heating time can vary based on ambient temperature and initial water temperature, typically taking up to 24 hours to reach maximum temperature from cold water.

4.3 Bubble Massage System

Enjoy the relaxing bubble massage.

• Once the water is at your desired temperature, press the BUBBLE button on the control panel.
• The 130 air jets will activate, providing a soothing massage.
• Press the BUBBLE button again to deactivate the jets.

5. Maintenance

5.1 Filter System

Regular filter maintenance is crucial for clean water.

• The hot tub includes 6 high-flow filters.
• Check and clean the filter cartridges regularly (e.g., weekly) to remove debris.
• Replace filter cartridges every 168 hours of operation or as needed, depending on usage and water quality.

Figure 5.1: The complete spa accessory kit, including the filter cartridges for maintenance.

5.2 Water Chemistry

Maintaining proper water chemistry is essential for hygiene and longevity of the hot tub.

• Regularly test the water pH and sanitizer levels using a test kit (not included).
• Adjust chemicals as necessary to maintain recommended levels (e.g., pH between 7.4-7.6, chlorine 1-3 ppm).
• Follow the instructions provided with your water treatment chemicals.

5.3 Cleaning and Drainage

Periodically clean the hot tub and drain the water for thorough maintenance.

• To drain, connect a garden hose to the drainage valve and open the valve.
• Clean the interior surfaces with a soft cloth and mild, non-abrasive cleaner.
• Rinse thoroughly and allow to dry completely before storage.

5.4 Storage

Proper storage ensures the longevity of your inflatable hot tub.

• Ensure the tub is completely dry before deflating and folding.
• Deflate the tub and its lid.
• Fold neatly and place in the provided storage bag.
• Store in a dry, temperate location, away from direct sunlight and extreme temperatures.

6. Troubleshooting

If you encounter issues, refer to these common solutions before contacting support.

• Hot Tub Not Heating:
  • Ensure the heater button is activated on the control panel.
  • Check that the power supply is stable and connected.
  • Verify the insulated cover is securely in place to prevent heat loss.
  • Allow sufficient time for heating (up to 24 hours for initial heating from cold).
• Bubbles Not Working:
  • Ensure the bubble button is activated on the control panel.
  • Check for any blockages in the air jet system.
• Water Not Clean:
  • Clean or replace filter cartridges regularly.
  • Test and adjust water chemistry (pH, sanitizer levels).
  • Ensure the filtration system is running for adequate periods.
• Water Leakage:
  • Check all valve connections and caps for tightness.
  • Inspect the tub for punctures. Use the provided repair kit for small holes.

7. Warranty and Support

This SEGMART hot tub is built with durable construction for long-lasting performance. For specific warranty details or technical assistance, please refer to the warranty card included with your product or contact SEGMART customer support. Our dedicated customer support team is available to answer any questions or provide assistance, ensuring a reliable and safe spa experience.

For further assistance, please visit the official SEGMART store or contact their customer service directly.