Important Safety Information
Please read and understand all instructions before assembly and use. Failure to follow these instructions may result in injury or damage to the product.
- Exercise caution around sharp edges when handling and assembling metal slats.
- Do not exceed the maximum weight capacity of 1000 pounds for this bed frame.
- Ensure all components are properly assembled and tightened according to the instructions to prevent instability or collapse.
- Keep small parts away from children during assembly to prevent choking hazards.
- Periodically check all connections to ensure they remain tight.
Package Contents
Before beginning assembly, verify that all parts listed below are present and undamaged. If any parts are missing or damaged, please contact customer support.
- Headboard (1)
- Side Rails (2)
- Footboard (1)
- Metal Slats (Set)
- Storage Drawers (4) - includes drawer frames, fronts, and wheels
- Center Support Beam and Legs (1 set)
- Hardware Pack (Screws, bolts, Allen wrench, etc.)
- Installation Manual (This document)

Figure 1: Overview of bed frame components and key dimensions. This image displays the headboard, footboard, side rails, metal slat system, and storage drawers, along with their approximate measurements.
Setup and Assembly Instructions
Assembly typically requires two adults. Please follow these steps carefully.
- Prepare the Area: Clear a spacious area for assembly. Lay out all components on a soft, clean surface to prevent scratches.
- Attach Headboard and Footboard to Side Rails: Connect the side rails to the headboard and footboard using the provided bolts and hardware. Ensure all connections are secure but do not fully tighten until the frame is fully assembled.
- Install Center Support: Attach the center support beam and its legs to the designated points on the bed frame. Adjust the legs to ensure they firmly touch the floor.
- Install Metal Slats: Place the metal slats onto the side rails. The slats feature a snap-in design for secure stability. Ensure each slat is properly seated and locked into place. Apply the included EVA silent foam tape to the metal frame where slats rest to minimize noise.
- Assemble Storage Drawers: Assemble the four storage drawers according to their individual instructions. Attach the wheels to the bottom of each drawer.
- Insert Drawers: Slide the assembled drawers into the designated spaces under the bed frame.
- Final Tightening: Once the entire frame is assembled, go back and securely tighten all bolts and screws. Do not overtighten.

Figure 2: Detail of the efficient embedded assembly method for metal slats and the application of noise-free foam tape for a quiet sleeping environment.
Operating Instructions
Using the Storage Drawers
Your LUXOAK bed frame is equipped with four spacious storage drawers designed for easy access and organization.
- Opening Drawers: Gently pull the drawer front to slide the drawer out from under the bed. The drawers are fitted with wheels for smooth movement on various floor surfaces.
- Closing Drawers: Push the drawer back into its compartment until it is fully recessed under the bed. Each drawer features a latch mechanism to prevent it from sliding out automatically. Ensure the latch engages when the drawer is fully closed.
- Capacity: Distribute weight evenly within the drawers. Avoid overloading to ensure smooth operation and prevent damage to the drawer or its wheels.

Figure 3: Illustration of the four under-bed storage drawers, highlighting their wheels for easy mobility and the latch system for secure closure.
Video 1: Demonstration of the 4 storage drawers, showcasing their sliding mechanism and ample space for organizing bedroom essentials.
Maintenance
Proper care will extend the life and appearance of your bed frame.
- Cleaning: Dust regularly with a soft, dry cloth. For spills, wipe immediately with a damp cloth and dry thoroughly. Avoid harsh chemicals or abrasive cleaners, which can damage the finish.
- Fasteners: Periodically check all bolts and screws to ensure they are tight. Re-tighten as necessary, but do not overtighten.
- Drawer Wheels: Keep drawer wheels free of debris to ensure smooth operation.
- Avoid Direct Sunlight: Prolonged exposure to direct sunlight can cause wood finishes to fade or crack.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Bed frame makes noise (squeaking/creaking) | Loose connections; friction between metal parts; missing EVA foam tape. |
|
| Drawers are difficult to open/close or get stuck | Obstruction; damaged wheels; overloaded drawer. |
|
| Bed frame feels unstable | Loose connections; improper assembly of center support. |
|
Specifications
| Model Number | BPB022 |
| Size | King |
| Product Dimensions (L x W x H) | 82.7"L x 77"W x 48.8"H |
| Material | Metal, Wood |
| Color | Dark Rustic Oak |
| Style | Farmhouse |
| Number of Drawers | 4 |
| Maximum Weight Recommendation | 1000 pounds |
| Compatible Mattress Height | 8-16 inches |
| Item Weight | 107.2 pounds |

Figure 4: The LUXOAK King Size Bed Frame without a mattress, illustrating the robust metal slat support system and overall structure.
Warranty and Customer Support
For any questions, missing parts, or concerns regarding your LUXOAK King Size Wooden Bed Frame, please contact the seller directly through your purchase platform or refer to the contact information provided with your order.
Please retain your proof of purchase for any warranty claims or support inquiries.