Introduction
This manual provides essential information for the safe and efficient operation of your RadioMaster Boxer Crush EdgeTX 2.4G 16CH Transmitter. Please read this manual thoroughly before using the device to ensure proper setup, operation, and maintenance.
The RadioMaster Boxer Crush is a high-performance radio control transmitter featuring the EdgeTX operating system and an internal ExpressLRS RF module. It is designed for precision control and reliability in various RC applications.
What's in the Box
- RadioMaster Boxer Crush Transmitter
- USB-C Cable
- Adjustable T-shape Antenna
- Quick Start Guide
- Sticker Set
- (Optional) Carrying Case
Image: The RadioMaster Boxer Crush transmitter in green, shown with its carrying case, USB-C cable, and other accessories.
Setup
1. Battery Installation
The Boxer Crush is designed to accommodate a 2S 6200mAh battery pack (not included) for extended operation. Ensure correct polarity when installing the battery.
Video: This video demonstrates the battery installation process for the Radiomaster Boxer M2 ELRS Portable RC Transmitter, showing how to open the battery compartment and connect the battery.
2. Antenna Attachment
Attach the adjustable and removable T-shape antenna to the designated port on the top of the transmitter. The antenna can be folded for easy transport.
3. Initial Power On and Calibration
Press and hold the power button to turn on the transmitter. Follow the on-screen prompts for initial setup. It is crucial to perform joystick calibration for accurate control. Refer to the video below for a calibration guide.
Video: This video provides a step-by-step guide on how to calibrate the remote control, demonstrating the joystick movements and menu navigation required for accurate setup.
Operating Instructions
EdgeTX Firmware
The Boxer Crush comes preinstalled with EdgeTX firmware, offering a highly customizable and user-friendly interface. Navigate through menus using the system buttons (SYS, RTN, PAGE>, PAGE<, TELE) and the scroll wheel.
ExpressLRS RF System
The internal ExpressLRS module supports a 1,000Hz refresh rate, providing ultra-low latency control. Ensure your receiver is compatible with ExpressLRS and properly bound to the transmitter.
AG01 Hall Gimbals
The CNC Aluminum AG01 Hall-effect Gimbals provide precise and smooth control. These gimbals are known for their durability and accuracy, enhancing your flying experience.
Image: Front view of the RadioMaster Boxer Crush transmitter in Cherry Red, showcasing the AG01 Hall Gimbals and the overall control layout.
Switches and Buttons
- Low-profile Latching SE Switch: For functions requiring a persistent on/off state.
- Momentary SF Switch: For functions requiring a temporary activation.
- Programmable RGB Buttons: Six configurable buttons for custom functions and visual feedback.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the transmitter. Avoid using harsh chemicals or solvents.
- Firmware Updates: Regularly check the official RadioMaster website for firmware updates to ensure optimal performance and access to new features. Updates can be performed via the single USB-C connector.
- Battery Care: Store the battery in a cool, dry place. Do not overcharge or over-discharge the battery.
- Storage: When not in use, store the transmitter in its protective carrying case to prevent damage.
Troubleshooting
- Transmitter not powering on: Check battery connection and charge level. Ensure the battery is properly installed.
- No control response: Verify that the receiver is correctly bound to the transmitter and that the drone's flight controller is configured for the correct protocol. Re-calibrate gimbals if necessary.
- Intermittent signal: Ensure the antenna is securely attached and fully extended. Avoid operating near sources of strong electromagnetic interference.
- Screen issues: If the screen is unresponsive or displaying incorrectly, try restarting the transmitter. If the issue persists, check for firmware updates.
Specifications
| Feature | Detail |
|---|---|
| Model | Boxer Crush EdgeTX 2.4G 16CH Transmitter |
| Brand | RadioMaster (Manufactured by Xiangtat) |
| Gimbals | CNC Aluminum AG01 Hall-effect Gimbals |
| Firmware | EdgeTX (Preinstalled) |
| RF System | Internal ExpressLRS Module (1,000Hz refresh rate) |
| Dimensions | 5 x 4 x 3 inches |
| Recommended Age | 15 years and up |
| Battery Compatibility | 2S 6200mAh pack (not included) |
| Charging | USB-C with Smart Balance Charging |
Warranty Information
This product is covered by a manufacturer's warranty. Please refer to the warranty card included in your product packaging or visit the official RadioMaster website for detailed warranty terms and conditions. Keep your proof of purchase for warranty claims.
Support
For technical support, troubleshooting assistance, or general inquiries, please visit the RadioMaster official website or contact their customer service team. Online resources, FAQs, and community forums are also available to help you get the most out of your transmitter.
Official Website: www.radiomasterrc.com