GarveeHome Twin XL Upholstered Bed Frame (Model BT014) - Instruction Manual

1. Introduction

Thank you for choosing the GarveeHome Twin XL Upholstered Bed Frame. This manual provides essential information for the safe assembly, operation, and maintenance of your new bed frame. Please read all instructions carefully before beginning assembly and retain this manual for future reference.

Figure 1: Assembled GarveeHome Twin XL Upholstered Bed Frame.

2. Safety Information

WARNING: Always supervise children around this bed frame. Ensure all parts are securely fastened before use. Follow assembly instructions carefully to prevent instability. Not intended for children under 3 years old due to potential choking hazards from small parts.

• Keep all small parts and packaging materials away from children during assembly.
• Ensure all bolts and screws are tightened securely before use. Periodically check and re-tighten all fasteners.
• Do not stand on the bed frame or use it as a trampoline.
• Do not use power tools for assembly unless specifically instructed, as overtightening may damage components.
• Place the bed frame on a level surface to prevent wobbling and instability.

3. Package Contents

Verify that all components are present before beginning assembly. If any parts are missing or damaged, please contact customer service.

Parts List:

• Upholstered Headboard
• Side Rails (2)
• Footboard
• Wooden Slats (12) with Velcro
• Center Support Beam
• Support Legs (for center beam)
• Bed Legs (4)

Hardware & Tools:

• Assembly Screws and Bolts
• Allen Wrench (Included)
• Instruction Manual (This document)

Figure 2: All parts and hardware included in the package.

4. Assembly Instructions

Assembly typically takes about 30 minutes for two people. Follow these steps carefully.

1. Attach Legs to Headboard and Footboard: Secure the four bed legs to the designated corners of the headboard and footboard using the provided screws. Ensure they are tightly fastened.
2. Connect Side Rails: Attach the side rails to the headboard and footboard. Align the pre-drilled holes and insert the bolts, tightening them with the Allen wrench.
3. Install Center Support Beam: Place the center support beam along the middle of the bed frame. Attach the support legs to the center beam and ensure they are securely positioned to the floor.
4. Position Wooden Slats: Lay the wooden slats across the bed frame. The slats are designed with Velcro strips to adhere to the frame, preventing movement and noise. Press each slat firmly onto the Velcro strips on the side rails.

Figure 3: Wooden slats with Velcro for secure, noise-free installation.

Figure 4: Sturdy metal frame construction for enhanced stability.

5. Product Features

• Elegant Scallop Headboard: The upholstered headboard features a charming scallop design, filled with high-density sponge for comfort and safety.
• Berber Fleece Fabric: Covered in soft, skin-friendly Berber fleece, mimicking natural sheepskin for a cozy touch.
• Sturdy and Noise-Free Construction: Built with a solid frame and 12 wooden slats, providing exceptional support and stability without squeaks.
• No Box Spring Needed: The robust wooden slat system eliminates the need for a box spring.
• Low Profile Design: Safe for children, allowing easy access in and out of bed.

Figure 5: Detail of the soft Berber fleece upholstered headboard.

6. Specifications

Figure 6: Product dimensions and material overview.

7. Care and Maintenance

• Cleaning: For the Berber fleece upholstery, gently spot clean with a mild detergent and a damp cloth. Avoid harsh chemicals or abrasive cleaners.
• Dusting: Regularly dust the frame and headboard with a soft, dry cloth.
• Inspection: Periodically check all bolts and screws to ensure they remain tight. Re-tighten as necessary to maintain stability.
• Avoid Direct Sunlight: Prolonged exposure to direct sunlight may cause fading of the fabric.

8. Troubleshooting

• Bed Frame is Wobbly: Ensure all bolts and screws are fully tightened. Check that the center support beam and its legs are properly aligned and making firm contact with the floor.
• Squeaking Noises: Verify that all wooden slats are securely attached to the Velcro strips on the side rails. Re-tighten any loose fasteners.
• Parts Don't Align: Double-check the instruction manual to ensure parts are oriented correctly. Sometimes parts can be installed backward.

9. Warranty and Support

GarveeHome products are designed for quality and durability. If you encounter any problems with your bed frame, or if you have questions regarding assembly or parts, please do not hesitate to contact our customer service team. Refer to your purchase documentation for specific warranty details and contact information.

We are committed to providing excellent support and ensuring your satisfaction with our products.