Introduction
Thank you for choosing the Aeitto Nugget Ice Maker. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new ice machine. Please read it thoroughly before first use and retain it for future reference.
Image: The Aeitto Nugget Ice Maker, a compact black unit, shown with a full basket of nugget ice, an ice scoop, and a glass containing a blue beverage with ice, highlighting its primary function.
Key Features
- Strong Ice Making Capacity: Produces up to 55lbs of nugget ice per day with a high-efficiency compressor and low noise level.
- Larger Water Tank & Ice Basket: Features a 3.6 L water tank and a 3.2 lb removable ice basket for extended ice production without frequent refills.
- Rapid Ice Release: Advanced technology allows ice release in approximately 5 minutes.
- Chewable & Crunchy Nugget Ice: Produces soft, chewable, and tooth-friendly nugget ice, ideal for various beverages.
- Automatic Ice Making Cycle: Automatically stops when the ice basket is full and resumes when ice levels drop, ensuring continuous availability.
- Auto-Cleaning Function: Simplifies maintenance with a one-touch cleaning cycle.
Setup
Unpacking
- Carefully remove the ice maker from its packaging.
- Remove all packing materials, including foam, tape, and any protective film.
- Inspect the unit for any shipping damage. If damaged, do not operate and contact customer support.
Placement
- Place the ice maker on a flat, stable, and level surface.
- Ensure adequate ventilation around the unit. Maintain at least 6 inches (15 cm) of space from walls or other appliances.
- Avoid placing the unit near heat sources (e.g., ovens, radiators) or in direct sunlight.
- Ensure the ambient temperature is between 50°F (10°C) and 90°F (32°C) for optimal performance.
- Do not place the ice maker in an enclosed cabinet.
Initial Cleaning
Before first use, it is recommended to clean the interior of the ice maker.
- Remove the ice basket and ice scoop.
- Clean the interior with a soft cloth dampened with warm water and a mild detergent.
- Rinse thoroughly with clean water.
- Run the self-cleaning cycle (refer to Maintenance section for details).
- Discard the first few batches of ice produced to ensure cleanliness.
Image: An exploded view of the Aeitto Nugget Ice Maker, highlighting the large 3.6-liter water tank at the bottom and the 3.2-pound removable ice basket positioned above it, demonstrating the unit's capacity.
Operating Instructions
Control Panel Overview
The control panel is located on the top of the unit and features indicator lights and buttons for easy operation.
- MAKING ICE Indicator: Illuminates when the unit is actively producing ice.
- ICE FULL Indicator: Illuminates when the ice basket is full. The unit will pause ice production.
- ADD WATER Indicator: Illuminates when the water tank needs refilling. The unit will pause ice production.
- CLEAN (Hold for 3 Sec) Button: Initiates the self-cleaning cycle.
- POWER Button: Turns the unit On or Off.
Adding Water
- Ensure the unit is powered off.
- Open the top lid.
- Carefully pour clean, potable water into the water tank. Do not exceed the MAX fill line.
- Close the top lid securely.
Starting Ice Production
- Plug the ice maker into a grounded electrical outlet.
- Press the POWER button to turn on the unit. The "MAKING ICE" indicator will illuminate.
- The first batch of ice will typically be ready in approximately 5 minutes.
- The unit will continue to make ice until the "ICE FULL" indicator illuminates or the "ADD WATER" indicator illuminates.
Image: A close-up view inside the ice maker showing freshly produced nugget ice being released into the ice basket, illustrating the rapid ice release feature.
Automatic Ice Making Cycle
The ice maker is equipped with an infrared sensor to detect ice levels. When the ice level reaches the sensor, the unit will automatically pause ice production. Production will resume after approximately 30 minutes if the ice level drops below the sensor, ensuring a continuous supply of ice.
Image: A diagram illustrating the automatic continuous ice making function, showing an infrared sensor detecting the ice level and indicating that ice production pauses when full and resumes when ice is removed.
Note: This ice maker does not have a refrigeration function for storing ice long-term. It is recommended to transfer produced ice to a freezer for storage.
Maintenance
Auto-Cleaning Function
The ice maker features an auto-cleaning function to help maintain hygiene and prevent limescale buildup.
- Ensure the water tank is filled with clean water.
- Press and hold the CLEAN (Hold for 3 Sec) button for 3 seconds. The unit will enter the cleaning cycle.
- The cleaning cycle typically takes several minutes. The unit will circulate water to clean internal components.
- Once the cycle is complete, drain the water from the unit (refer to Draining Water section).
- It is recommended to run the auto-cleaning function regularly, especially if using hard water. For stubborn limescale, a descaling solution may be needed (follow descaler product instructions).
Image: A diagram illustrating the auto-cleaning function of the ice maker, showing water circulating through the system to clean internal components and remove limescale, promoting fresh ice and healthy operation.
Draining Water
To drain water from the unit, locate the drain plug at the bottom or back of the unit (consult diagram in physical manual if available). Place a container beneath the plug, remove it, and allow all water to drain. Reinsert the plug securely after draining.
Storage
If the ice maker will not be used for an extended period:
- Perform a thorough cleaning and draining cycle.
- Ensure the interior is completely dry to prevent mold or mildew growth.
- Store the unit in a cool, dry place, away from direct sunlight and extreme temperatures.
Troubleshooting
Before contacting customer support, please refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Ice maker not turning on. | Not plugged in; Power outage; Unit malfunction. | Ensure power cord is securely plugged in. Check household circuit breaker. Contact customer support if issue persists. |
| "ADD WATER" indicator is on. | Water tank is empty or water level is too low. | Add clean, potable water to the water tank up to the MAX fill line. |
| "ICE FULL" indicator is on, but basket is not full. | Ice sensor is blocked or dirty. | Clean the ice sensor with a soft cloth. Ensure no ice cubes are blocking the sensor. |
| No ice production or very little ice. | Insufficient water; Ambient temperature too high; Air vent blocked; Unit needs cleaning. | Check water level. Move unit to a cooler location. Ensure proper ventilation. Run auto-cleaning cycle. |
| Ice tastes strange or has odor. | Unit needs cleaning; Stale water; Water quality issue. | Perform a thorough cleaning cycle. Replace water regularly. Use filtered water if tap water quality is poor. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | WBJ15NC |
| Brand | Aeitto |
| Product Dimensions (D x W x H) | 16.9"D x 9.84"W x 16.9"H |
| Daily Ice Production Capacity | Up to 55 lbs/day |
| Water Tank Capacity | 3.6 Liters |
| Ice Basket Capacity | 3.2 lbs |
| Refrigerant | R600a |
| First Ice Release Time | Approx. 5 minutes |
What's in the Box
- Nugget Ice Maker x 1
- Ice Scoop x 1
- Ice Basket x 1
Warranty and Support
Aeitto products are designed and manufactured to the highest quality standards. For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official Aeitto website. Please have your model number (WBJ15NC) and purchase date available when contacting support.