Please read and understand all instructions before beginning installation. Failure to do so may result in electric shock, fire, or other injuries that could be hazardous or even fatal. Keep these instructions for future reference.
Always turn off the main power supply at the circuit breaker before installing or servicing the fixture.
Consult a qualified electrician if you are unsure about the installation process.
Use only bulbs of the specified type and wattage. Do not exceed the maximum wattage.
Ensure all electrical connections are secure and comply with local codes and ordinances.
Do not install this fixture in wet locations unless specifically rated for such use. This fixture is rated for indoor use only.
2. Package Contents
Carefully unpack your fixture and check that all parts are included. Retain all packaging material until installation is complete to prevent loss of small parts.
Fixture Body with Back Plate
Clear Glass Shades (4 pieces)
Mounting Hardware (Crossbar, Screws, Wire Nuts)
Instruction Manual
Note: Bulbs are not included and must be purchased separately.
3. Setup and Installation
Before you begin, ensure the power is turned off at the circuit breaker. This fixture can be mounted with the lights facing up or down.
3.1 Tools Required (Not Included)
Screwdriver (Phillips and Flathead)
Wire Strippers
Electrical Tape
Pliers
Safety Glasses
3.2 Installation Steps
Turn Off Power: Locate the circuit breaker controlling the light switch and turn it off. Verify power is off using a voltage tester.
Prepare Mounting: Attach the mounting crossbar to the junction box using the provided screws. Ensure it is securely fastened.
Wire Connections:
Connect the fixture's black wire to the house's black (hot) wire using a wire nut.
Connect the fixture's white wire to the house's white (neutral) wire using a wire nut.
Connect the fixture's ground wire (bare copper or green) to the house's ground wire and to the mounting crossbar's ground screw.
Secure all wire connections with electrical tape.
Mount Fixture: Carefully tuck all wires into the junction box. Align the fixture's back plate with the mounting screws on the crossbar and secure it with the decorative nuts.
Install Glass Shades: Attach each clear glass shade to the fixture by screwing it onto the socket assembly. Ensure they are finger-tight.
Install Bulbs: Screw in the required E26 base bulbs (not included) into each socket. Do not exceed 60W per bulb.
Restore Power: Turn the power back on at the circuit breaker and test the light fixture.
Image: The VINLUZ vanity light can be installed with the glass shades facing upwards or downwards, offering versatile aesthetic options.
Image: Detailed dimensions of the fixture (23.82 inches wide, 9.65 inches high) and a visual guide to compatible E26 base bulbs (max 60W, 110-240V).
4. Operating Instructions
This VINLUZ vanity light is designed for simple operation once installed.
Power On/Off: Use your standard wall switch to turn the light fixture on or off.
Bulb Requirements: The fixture uses E26 standard base bulbs. Each socket supports a maximum of 60 watts. Do not exceed this wattage.
Dimmable Functionality: This fixture is compatible with a dimmer switch (not included). If you wish to use a dimmer, ensure you install a compatible E26 dimmable bulb and a suitable dimmer switch.
Image: Visual representation of the light fixture in both 'Turn On' and 'Turn Off' states, illustrating how different bulb color temperatures can create varied ambiances.
5. Maintenance
Regular maintenance will help preserve the appearance and functionality of your VINLUZ vanity light.
Cleaning: To clean the fixture, ensure the power is off. Wipe the brushed nickel finish with a soft, dry cloth. For the glass shades, use a mild glass cleaner and a soft cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish.
Bulb Replacement: Always turn off the power before replacing bulbs. Allow bulbs to cool completely before handling. Replace with E26 base bulbs, not exceeding 60 watts.
Glass Shade Replacement: In case of a broken glass shade, contact VINLUZ customer service for a free replacement.
6. Troubleshooting
If you encounter issues with your VINLUZ vanity light, refer to the following common problems and solutions:
Problem
Possible Cause
Solution
Light does not turn on.
No power to the fixture.
Loose wire connection.
Faulty bulb.
Check circuit breaker and wall switch.
Verify all wire connections are secure (ensure power is off first).
Replace bulb with a new, working one.
Light flickers.
Loose bulb.
Incorrect bulb type for dimmer (if applicable).
Loose wire connection.
Tighten bulb securely.
Ensure dimmable bulbs are used with a dimmer switch.
Check wire connections (ensure power is off first).
Glass shade is broken.
Accidental damage.
Contact VINLUZ customer service for a free replacement.
7. Specifications
Model Number
1751-4W-SN
Brand
VINLUZ
Manufacturer
VINLUZ
Style
Modern, Farmhouse, Industrial
Color/Finish
Brushed Nickel
Material
Metal, Clear Glass
Item Weight
7.83 pounds
Package Dimensions
24.25 x 12.75 x 6.25 inches
Specific Uses
Indoor use only (Bathroom, Living Room, Dining Room, Bedroom, Hallway)
Power Source
AC
Voltage
110-240V
Bulb Base
E26 Standard
Max Wattage per Bulb
60W
Batteries Required
No
Image: Detailed view highlighting the brushed nickel finish, clear glass shade, and the E26 bulb base (bulb not included).
8. Warranty and Customer Support
VINLUZ is committed to providing quality products and customer satisfaction.
General Support: For any quality issues, skill problems, or replacement parts, please contact the original manufacturer, LightingPlus. You can typically find their contact information on the platform where you purchased the product (e.g., Amazon seller page).
Contact Method: On Amazon, you can click on "LightingPlus" (the seller name) and then click on "Ask a question" to contact them directly.
