HJC i80 Roki

Download PDF
Contents

HJC i80 Roki Modular Motorcycle Helmet User Manual

Model: i80 Roki

1. Introduction

Thank you for choosing the HJC i80 Roki Modular Motorcycle Helmet. This manual provides essential information for the safe and effective use, maintenance, and care of your helmet. Please read it thoroughly before using your helmet and retain it for future reference.

2. Safety Information

Your safety is paramount. This helmet is designed to provide protection, but no helmet can protect against all possible impacts. Always ride responsibly and follow all traffic laws.

2.1 DOT Approval

The HJC i80 Roki Modular helmet meets stringent DOT FMVSS 218 standards. This means it has undergone rigorous testing for energy absorption, penetration resistance, and secure chin strap integrity, as well as meeting labeling requirements for on-road motorcycle helmets.

Helmet undergoing DOT testing for impact resistance

Image: Illustration of a helmet undergoing impact testing, demonstrating compliance with DOT standards.

2.2 Proper Fit

A helmet must fit snugly and comfortably to provide maximum protection. Ensure the helmet does not move freely on your head when the chin strap is fastened. If the helmet is too loose, it may shift during an impact, reducing its protective capabilities.

2.3 Chin Strap

Always fasten the double-D ring chin strap securely before riding. The strap should be tight enough so that you cannot remove the helmet by pulling it from the back.

3. Features Overview

The HJC i80 Roki Modular Helmet is engineered with advanced features for comfort, safety, and performance.

  • DOT-Approved: Meets FMVSS 218 standards for maximum safety.
  • Pinlock Ready HJ-44 Visor: Offers 99% UV protection and an anti-scratch coating.
  • Sturdy Exterior: Constructed from a Polycarbonate-ABS blend for impact resistance and lightweight design.
  • Comfortable Interior: Features removable and washable crown and cheek pads for easy maintenance and a customizable fit.
  • Advanced Channeling Ventilation System: Strategically placed top and lower vents to expel heat and humidity.
  • Integrated Sun Shield (HJ-V12): Improves peripheral vision and blocks sunlight, with anti-fog and anti-scratch coating.

3.1 Exterior Construction (APC)

The helmet shell is made from an Advanced Polycarbonate Compound (APC). This blend of high-grade polycarbonate with high impact strength ABS results in a strong, impact-resistant, yet lightweight design. The helmet also features a wind tunnel-tested peak visor for stability and reduced drag.

Rear view of the HJC i80 helmet showing its polycarbonate shell design

Image: Rear view of the HJC i80 helmet, highlighting the Advanced Polycarbonate Compound shell construction.

3.2 HJ-44 Visor and Pinlock

The HJ-44 visor provides 99% UV-A & B protection and has an anti-scratch coating. It is Pinlock-ready, meaning it can accommodate a Pinlock anti-fog insert (standard with Pinlock).

Front view of the HJC i80 helmet with the HJ-44 visor

Image: Front view of the HJC i80 helmet, showcasing the HJ-44 visor.

3.3 HJ-V12 Sun Shield

An integrated HJ-V12 sun shield is included, offering improved peripheral vision and effective sunlight blocking to reduce eye strain. This sun shield also features anti-fog and anti-scratch coatings.

Side view of the HJC i80 helmet with the HJ-V12 sun shield deployed

Image: Side view of the HJC i80 helmet, demonstrating the integrated HJ-V12 sun shield in use.

3.4 Advanced Channeling Ventilation System

The helmet incorporates an Advanced Channeling Ventilation System with strategically placed top and 2-step toggle lower vents. This system ensures full front-to-back airflow, effectively flushing heat and humidity out of the helmet for rider comfort.

Diagram illustrating the airflow through the HJC i80 helmet's ventilation system

Image: Diagram showing the Advanced Channeling Ventilation System, illustrating airflow paths within the helmet.

4. Setup and Installation

4.1 Initial Fit Adjustment

Upon first use, ensure the helmet fits correctly. The cheek pads are interchangeable across all shell sizes, allowing for a customizable fit. If the fit is too loose or too tight, consider adjusting the cheek pads or consulting a professional for assistance.

4.2 Visor Installation/Removal

The HJ-44 visor can be removed and installed without tools. Refer to the quick-release mechanism on the side of the helmet for instructions. Ensure the visor is securely latched before riding.

4.3 Pinlock Insert Installation

To install the Pinlock anti-fog insert:

  1. Remove the HJ-44 visor from the helmet.
  2. Flex the visor slightly to flatten it.
  3. Align the Pinlock insert with the pins on the inside of the visor.
  4. Press the edges of the Pinlock insert onto the pins until it seals against the visor.
  5. Ensure there are no gaps between the Pinlock and the visor.
  6. Reinstall the visor onto the helmet.

5. Operation

5.1 Modular Function

The i80 Roki is a modular helmet, allowing the chin bar to be raised. To operate:

  1. Locate the release mechanism, typically at the front center of the chin bar.
  2. Press the release button and lift the chin bar upwards until it locks into the open position.
  3. To close, press the release button again and lower the chin bar until it securely latches.

Warning: Do not ride with the chin bar in the open position at high speeds or in situations where full facial protection is required.

5.2 Sun Shield Operation

The integrated HJ-V12 sun shield can be deployed or retracted using the slider mechanism located on the side of the helmet. Slide it down to deploy and up to retract. The sun shield offers two settings for adjustment.

5.3 Ventilation System

Adjust the top and lower vents to control airflow. The lower vents have a 2-step toggle for fine-tuning ventilation. Open vents for maximum airflow to reduce heat and humidity, and close them for reduced airflow in colder conditions.

6. Maintenance

6.1 Cleaning the Exterior

Clean the helmet exterior with a soft cloth and mild soap and water. Avoid abrasive cleaners, solvents, or petroleum-based products, as these can damage the helmet's finish and materials.

6.2 Cleaning the Interior

The crown and cheek pads are removable and washable.

  1. Carefully remove the interior pads.
  2. Hand wash with mild soap and lukewarm water.
  3. Rinse thoroughly and allow to air dry completely before reinstalling.
  4. Do not machine wash or tumble dry.

6.3 Visor and Sun Shield Care

Clean visors and sun shields with a soft, damp cloth and mild soap. Do not use harsh chemicals or abrasive materials. For Pinlock inserts, clean gently with a soft, damp cloth only, avoiding rubbing the inner surface.

6.4 Storage

Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use a helmet bag to protect it from scratches and dust.

7. Troubleshooting

  • Visor Fogging: Ensure the Pinlock insert is correctly installed and sealed. If fogging persists, check for proper ventilation or consider replacing the Pinlock insert if it's old or damaged.
  • Loose Fit: Check if the cheek pads are correctly installed. Consider purchasing thicker cheek pads for a more snug fit, as they are interchangeable.
  • Excessive Noise: Ensure all vents are closed if noise is an issue. Check that the chin bar is fully latched in the closed position.
  • Chin Bar Not Latching: Verify that the chin bar mechanism is free of debris and operates smoothly. Do not force it; if it remains stuck, seek professional inspection.

8. Specifications

FeatureDetail
Model Namei80 Roki
BrandHJC
Safety StandardDOT FMVSS 218 Approved
Outer MaterialPolycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) Blend
Inner MaterialFoam (Removable & Washable)
Visor TypeHJ-44 Pinlock Ready, 99% UV Protection, Anti-scratch
Sun ShieldIntegrated HJ-V12, Anti-fog, Anti-scratch
VentilationAdvanced Channeling Ventilation System (ACS) with Top & 2-step Lower Vents
Chin StrapDouble-D Ring
Item WeightApproximately 4.09 Pounds (varies by size)
Manufacturer Part Number0854-1021-03
UPC190501326201

9. Official Product Video

Video: Official HJC i80 Modular Helmet overview, demonstrating features and usage. Duration: 0:39.

10. Warranty and Support

HJC Helmets typically come with a manufacturer's warranty covering defects in materials and workmanship. For specific warranty details, duration, and terms, please refer to the warranty card included with your helmet or visit the official HJC Helmets website.

For technical support, replacement parts, or further assistance, please contact HJC customer service through their official website or authorized dealers.

Important: Do not attempt to modify or repair the helmet yourself, as this may compromise its safety features and void the warranty.

© 2026 HJC Helmets. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.