1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your SRAM S700 10-speed Left Front Road Hydraulic Disc Brake and DoubleTap Lever. Designed for optimal stopping power and modulation, this system ensures reliable performance for road or cyclocross applications. Please read this manual thoroughly before use to ensure safety and prolong the life of your product.
2. Setup and Installation
The SRAM S700 hydraulic disc brake system is designed for straightforward installation. Ensure all components are present and undamaged before beginning.
- Hose Length: The system comes with a 950mm hose, suitable for left front brake configurations.
- Rotor Compatibility: This brake system is compatible with 160mm rotors for pavement use and 140mm rotors for off-road applications. Rotors are sold separately.
- Caliper and Piston Ratio: Features a road-specific caliper and piston ratio for optimized braking performance.
- Hardware: Includes direct mount hardware for secure installation.
- Lever Compatibility: Designed for use with SRAM S-700 hydraulic shift-brake levers.
Figure 2.1: SRAM S700 10-speed Left Front Road Hydraulic Disc Brake and DoubleTap Lever assembly, including the brake caliper and a compatible rotor. This image illustrates the complete brake system as it would appear when installed on a bicycle.
3. Operating Instructions
The SRAM S700 system provides precise control and efficient shifting and braking.
- DoubleTap Lever: The integrated DoubleTap lever allows for both upshifts and downshifts with a single lever movement, providing intuitive control.
- Braking Performance: Experience optimized stopping power and modulation, allowing for fine control over braking force in various conditions.
- Reach Adjustment: Both the brake and shift levers feature independent reach adjustment, allowing riders to customize the lever position for comfort and control.
- Front Derailleur Compatibility: This system is compatible with YAW front derailleurs, ensuring smooth and precise front shifting.
4. Maintenance
Regular maintenance is crucial for the longevity and optimal performance of your SRAM S700 brake system.
- Sealed System: The system is fully sealed to prevent contamination from dirt and debris, reducing the need for frequent internal cleaning.
- Bleed Port: The bleed port is easily accessed for convenient hydraulic fluid maintenance and bleeding procedures.
- Pad Wear Compensation: A high-capacity bladder within the system automatically compensates for pad wear, maintaining consistent lever feel and braking performance as pads wear down.
- Components: Features durable stainless steel backed pads and stainless hardware for corrosion resistance and long-term reliability.
- Cleaning: Regularly clean the exterior of the brake caliper and levers with a mild soap and water solution. Avoid harsh chemicals.
- Inspection: Periodically inspect brake pads for wear and replace them when necessary. Check hose for any signs of damage or leaks.
5. Troubleshooting
If you encounter issues with your SRAM S700 brake system, consider the following common solutions. For complex problems, it is recommended to consult a certified bicycle mechanic.
- Spongy Lever Feel: This often indicates air in the hydraulic system. Bleeding the brakes using the easily accessed bleed port may resolve this.
- Reduced Braking Power: Check brake pad wear. Worn pads will reduce braking efficiency. Also, inspect the rotor for contamination (e.g., oil) or excessive wear.
- Noise During Braking: Ensure rotors and pads are clean. Contamination or misaligned calipers can cause noise. Check for loose bolts.
- Lever Not Returning: Inspect the lever pivot for debris or damage. Ensure the hydraulic system is not overfilled.
- Fluid Leaks: Immediately address any fluid leaks. This could indicate a damaged hose, seal, or caliper. Do not ride the bicycle until the leak is repaired.
If these steps do not resolve the issue, professional service is advised.
6. Specifications
| Feature | Detail |
|---|---|
| Brand | SRAM |
| Model | S-700 Yaw |
| Part Number | 00.7018.171.002 |
| Material | Aluminum (Lever), Stainless Steel (Hardware, Pad Backing) |
| Hose Length | 950mm (Front) |
| Rotor Compatibility | 160mm (Pavement), 140mm (Off-road) - Rotor Sold Separately |
| Vehicle Service Type | Bicycle |
| Item Weight | 1.1 pounds |
| Product Dimensions | 16 x 8.5 x 4.2 inches |
| UPC | 710845759215 |
| GTIN | 00710845759215 |
7. Warranty and Support
For warranty information, technical support, or service inquiries regarding your SRAM S700 Hydraulic Disc Brake, please refer to the official SRAM website or contact their customer service directly. Keep your proof of purchase for any warranty claims.
You can find more information and contact details by visiting the official SRAM store or support pages:
