Introduction
The PRITECH Electric Foot Callus Remover (Model BCM-1852) is designed to effectively remove dead skin and calluses from your feet, providing a smooth and healthy appearance. This rechargeable, portable electronic foot file features multiple roller heads and adjustable speeds for personalized foot care.
Safety Information
- Always use on dry skin.
- Avoid applying excessive pressure to prevent injury.
- Do not use on broken or irritated skin.
- Keep the product away from water when not in use.
Product Overview
The PRITECH Electric Foot Callus Remover comes with various components designed for optimal performance and user convenience.
The PRITECH Electric Foot Callus Remover, shown with hands and feet in the background, highlighting its purpose for foot care.
The device includes three interchangeable quartz sand grinding heads: Extra Coarse for tough calluses, Regular Coarse for dead skin, and Gentle Coarse for daily maintenance.
Setup
Charging the Device
The device is equipped with a 1200mAh lithium battery. Before first use, fully charge the device.
- Locate the USB charging port at the bottom of the device.
- Connect the provided USB charging cable to the device and a suitable USB power source (e.g., laptop, power bank, wall adapter).
- The LED power display will indicate the charging status. A full charge takes approximately 130 minutes and provides about 120 minutes of continuous use.
The device features fast USB charging, compatible with various USB power sources like laptops, power banks, and wall sockets.
Attaching Roller Heads
To change or attach a roller head:
- Ensure the device is turned off.
- Gently press the release button on the side of the roller head and pull the head upwards to remove it.
- Align the desired roller head with the device and push it down until it clicks securely into place.
Illustration of how to easily attach and detach the different roller heads for various exfoliation needs.
Operating Instructions
Follow these steps for effective and safe use of your callus remover:
- Preparation: Start with dry feet for safety and better results.
- Power On: Press the power button to turn on the device. The LED display will show the current speed setting and battery level.
- Speed Adjustment: The device offers three speed modes (1700 r/pm, 1900 r/pm, 2100 r/pm). Press the power button repeatedly to cycle through the speeds to select your preferred intensity.
- Application: Gently apply the foot callus remover to the affected areas, avoiding broken or irritated skin. Use light pressure and do not go too deep into the skin to avoid pain or injury.
- Targeting Calluses: For tough calluses, you may need to repeat the process a few times. Move the device slowly over the area.
- Post-Treatment: After use, clean your feet and moisturize with foot cream.
The device features three adjustable speeds (1700, 1900, and 2100 RPM) to cater to different callus removal needs, from gentle to powerful.
A visual guide to the three-step foot care process: 1. Wash feet, 2. Grind calluses with the device, 3. Protect and moisturize feet.
Maintenance
Cleaning the Device
The PRITECH Electric Foot Callus Remover has a waterproof design (IPX6 rated), allowing for easy cleaning.
- Ensure the device is turned off and disconnected from any charging cable.
- Remove the roller head as described in the Setup section.
- Rinse the roller head and the main body of the device under running water. You may use mild soap if needed.
- Use the provided cleaning brush to remove any remaining dead skin particles from the roller head and device.
- Dry the foot callus remover thoroughly before storing it. Avoid frequent submersion of the entire device to prevent potential issues.
The device is IPX6 waterproof, allowing for easy cleaning under running water. The image shows disassembly, dust removal with a brush, and rinsing.
Replacing Roller Heads
Roller heads should be replaced when they show signs of wear or become less effective. Replacement heads can be purchased separately.
- Follow the steps for 'Attaching Roller Heads' to remove the old head and install a new one.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not turn on | Low battery or no charge | Charge the device fully using the provided USB cable. |
| Roller head stops spinning during use | Excessive pressure applied | Reduce pressure on the skin. The device has a safety feature to prevent injury from too much force. |
| Reduced effectiveness of roller head | Roller head is worn out or clogged | Clean the roller head or replace it with a new one. |
| Device not charging | Faulty cable or power source | Try a different USB cable or power adapter. Ensure the charging port is clean. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | BCM-1852 |
| Product Dimensions | 6.93 x 5.12 x 1.97 inches |
| Item Weight | 5.29 ounces (0.15 Kilograms) |
| Battery | 1200mAh Lithium (1 AA battery required, included) |
| Charging Time | Approx. 130 minutes |
| Operating Time | Approx. 120 minutes |
| Speed Settings | 3 (1700 r/pm, 1900 r/pm, 2100 r/pm) |
| Waterproof Rating | IPX6 |
| Material | Plastic |
| Color | White |
Warranty and Support
PRITECH products are manufactured to high-quality standards. For any issues, please contact our customer support. If you receive the product with any problems such as wear or stains, please contact us in the first instance and we will provide you with a solution.
For support, please visit the PRITECH Store on Amazon.
Legal Disclaimer
Statements regarding dietary supplements have not been evaluated by the FDA and are not intended to diagnose, treat, cure, or prevent any disease or health condition.
