Dasqua 2220-3575

Download PDF
Contents

Dasqua Heavy Duty Digital Caliper User Manual

Model: 2220-3575

Product Overview

The Dasqua 2220-3575 Heavy Duty Digital Caliper is a precision measuring instrument designed for accurate dimensional measurements. It features a sturdy stainless steel construction, a large jaw length, and fine adjustment capabilities, making it suitable for industrial applications. This caliper is manufactured in strict accordance with DIN862 standards and offers both data output and inch-metric conversion functions.

Dasqua Heavy Duty Digital Caliper

Figure 1: Overview of the Dasqua Heavy Duty Digital Caliper.

What's in the Box

  • Dasqua Heavy Duty Digital Caliper with Fine Adjustment

Key Features

  • Sturdy frame and large size for enhanced stability.
  • Constructed from solid stainless steel for durability.
  • Manufactured strictly in accordance with DIN862 standards.
  • Equipped with data output functionality.
  • Supports seamless inch-metric conversion.
Dasqua Caliper Features Diagram

Figure 2: Diagram highlighting key features and dimensions of the caliper.

Setup and Initial Operation

Unpacking and Inspection

Carefully remove the digital caliper from its packaging. Inspect the instrument for any signs of damage during transit. Ensure all components listed in the "What's in the Box" section are present.

Battery Installation (if applicable)

Locate the battery compartment, typically on the digital display unit. Insert the correct battery type with the correct polarity. Close the battery compartment securely.

Powering On and Zeroing

  1. Press the ON/OFF button to power on the caliper.
  2. Close the measuring jaws completely and firmly.
  3. Press the ZERO/SET button to set the display to zero. This establishes the reference point for all subsequent measurements.
Digital Display and Control Buttons

Figure 3: Close-up view of the digital display and control buttons (ON/OFF, ZERO/SET, ABS/INC, mm/in).

Operating Instructions

Measuring Techniques

The Dasqua Digital Caliper can perform external, internal, depth, and step measurements.

  • External Measurement: Use the large jaws to measure outside dimensions. Ensure the jaws are perpendicular to the workpiece.
  • Internal Measurement: Use the small upper jaws to measure inside dimensions.
  • Depth Measurement: Extend the depth rod from the end of the beam into a hole or recess.
  • Step Measurement: Use the end of the beam and the end of the sliding jaw to measure steps.
Caliper Jaws for Measurement

Figure 4: The measuring jaws of the caliper, used for external and internal measurements.

Inch/Metric Conversion

Press the mm/in button to switch between millimeter and inch display modes. The current unit will be indicated on the digital display.

Absolute/Incremental Measurement

Press the ABS/INC button to toggle between absolute and incremental measurement modes. In incremental mode, you can zero the display at any point to measure relative distances.

Fine Adjustment

The caliper is equipped with a fine adjustment mechanism. Use the knurled knob to make precise movements of the sliding jaw for accurate positioning before taking a reading.

Maintenance and Care

  • Cleaning: After each use, wipe the caliper clean with a soft, lint-free cloth. For stubborn dirt, use a mild, non-abrasive cleaning solution. Avoid using solvents that could damage the display or finish.
  • Lubrication: Periodically apply a thin film of light machine oil to the sliding surfaces to ensure smooth operation and prevent corrosion.
  • Storage: Store the caliper in its protective case in a dry, clean environment, away from direct sunlight, extreme temperatures, and corrosive substances.
  • Battery Replacement: Replace the battery when the display becomes dim or shows a low battery indicator. Refer to the battery installation steps.
  • Calibration: For critical applications, periodic calibration by a qualified technician is recommended to ensure continued accuracy.
Caliper Beam and Scale

Figure 5: The main beam of the caliper, which should be kept clean and lightly lubricated for optimal performance.

Troubleshooting

ProblemPossible CauseSolution
Display is blank or dim.Low or dead battery.Replace the battery. Ensure correct polarity.
Inaccurate readings.Jaws not properly closed before zeroing; dirt/debris on measuring surfaces; caliper not calibrated.Ensure jaws are clean and fully closed before zeroing. Clean measuring surfaces. Consider professional calibration.
Sliding jaw movement is stiff.Lack of lubrication; dirt/debris on the beam.Clean the beam thoroughly. Apply a thin film of light machine oil to the sliding surfaces.

Specifications

AttributeDetail
Model Number2220-3575
Measuring Range0-1500mm / 0-60 inches
Jaw Length150mm
MaterialSolid Stainless Steel
ComplianceDIN862
FeaturesData Output, Inch-Metric Conversion, Fine Adjustment
Product Dimensions78 x 18 x 10 inches
Product Weight25 Pounds
ManufacturerABS Import Tools Inc.
Country of OriginChina
UPC769053104812

Warranty and Support

For warranty information and technical support, please contact Dasqua customer service or refer to the official Dasqua website. Keep your purchase receipt as proof of purchase.

Manufacturer: ABS Import Tools Inc.

Brand: Dasqua

For further assistance, please visit the Dasqua Store on Amazon.

© 2024 Dasqua. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.