TILSWALL Shark 800 HVLP Paint Sprayer

1. Important Safety Instructions

Please read and understand all safety warnings and instructions before operating this paint sprayer. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.

• Work Area Safety: Keep the work area clean and well-lit. Do not operate the sprayer in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Ensure adequate ventilation.
• Personal Safety: Always wear appropriate personal protective equipment, including eye protection (safety glasses or goggles), respiratory protection (mask or respirator), gloves, and protective clothing. Avoid skin contact with paint and solvents.
• Electrical Safety: Do not expose the sprayer to rain or wet conditions. Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts.
• Material Safety: Always refer to the paint and solvent manufacturer's safety data sheets (SDS) for specific handling, storage, and disposal instructions. Do not spray flammable materials near open flames, pilot lights, or other ignition sources.
• Children and Bystanders: Keep children and bystanders away while operating a paint sprayer.

2. Product Overview and Components

The TILSWALL Shark 800 HVLP Paint Sprayer is designed for efficient and even application of various coatings. Familiarize yourself with its components before use.

Image: Main unit of the TILSWALL Shark 800 HVLP Paint Sprayer, showing its compact design.

Included Components:

• 1 x Paint Gun (main unit)
• 1 x Spray Can Cover
• 1 x 2.5-meter Air Hose
• 4 x Brass Nozzles (1mm, 1.5mm, 2mm, 3.0mm)
• 3 x Large Seals
• 3 x Small Seals
• 3 x Spray Can Shapes (for different spray patterns)
• 1 x Viscosity Cup
• 1 x Cleaning Needle
• 1 x Cleaning Brush

3. Setup

Proper setup ensures optimal performance and safety.

1. Assemble the Air Hose: Connect the 2.5-meter air hose securely to both the paint gun and the main power unit. Ensure all connections are tight to prevent air leaks.
2. Prepare the Paint:
   • Most paints require thinning for proper atomization with an HVLP sprayer. Use the included viscosity cup to measure the paint's viscosity.
   • Fill the viscosity cup with paint and time how long it takes for the paint to flow out. Refer to your paint manufacturer's recommendations for ideal viscosity. For ultra-smooth atomization, aim for approximately 100 DIN viscosity.
   • Gradually add the appropriate thinner (water for latex, mineral spirits for oil-based, etc.) and mix thoroughly until the desired viscosity is achieved.
3. Select the Nozzle: Choose one of the four brass nozzles (1mm, 1.5mm, 2mm, 3.0mm) based on the paint type and desired spray pattern. Smaller nozzles are for thinner materials and finer finishes, while larger nozzles are for thicker materials and faster coverage.
4. Fill the Container: The Tilswall Shark 800 features a side-fill design. You can easily add paint from the side without rotating the spray can, minimizing spillage and waste. Ensure the container is securely attached after filling.
5. Adjust the 45° Paint Straw: The paint straw is designed at a 45° angle to maximize paint usage and minimize waste. Ensure it is positioned correctly to draw paint efficiently from the container.

4. Operation

Follow these steps for effective and consistent paint application.

1. Power On: Plug the sprayer into a grounded electrical outlet.
2. Adjust Spray Pattern: The sprayer can be adjusted to three different spray patterns: horizontal, vertical, and circular. Rotate the air cap to select the desired pattern for your project.
3. Adjust Flow Control: Use the precision flow control dial to fine-tune the paint output. Start with a lower setting and gradually increase until you achieve the desired coverage and finish.
4. Test Spray: Before spraying your actual project, always perform a test spray on a piece of scrap material (cardboard, wood, etc.) to check the spray pattern, flow rate, and atomization. Adjust as necessary.
5. Spraying Technique:
   • Hold the sprayer perpendicular to the surface, maintaining a consistent distance (typically 6-12 inches).
   • Move the sprayer in smooth, even strokes, overlapping each pass by about 50%.
   • Release the trigger at the end of each pass to avoid paint buildup.
   • Apply multiple thin coats rather than one thick coat for a smoother, more durable finish.

5. Maintenance and Cleaning

Thorough cleaning after each use is crucial for the longevity and performance of your paint sprayer.

1. Empty Remaining Paint: Pour any unused paint back into its original container.
2. Initial Rinse: Fill the paint container with the appropriate cleaning solution (water for latex, mineral spirits for oil-based paints). Spray the cleaning solution through the sprayer into a waste container until it runs clear.
3. Disassembly: Disconnect the power. Carefully disassemble the paint gun, including the nozzle, air cap, and paint container.
4. Thorough Cleaning:
   • Clean all disassembled parts with the appropriate cleaning solution and the included cleaning brush and needle. Pay close attention to small passages and orifices to remove all paint residue.
   • Some areas may require careful attention with the cleaning needle to ensure no clogs remain.
   • Wipe down the exterior of the sprayer with a damp cloth. Do not immerse the main power unit in liquid.
5. Drying and Storage: Allow all parts to dry completely before reassembling. Store the sprayer in a clean, dry place, away from extreme temperatures.

6. Troubleshooting

Refer to this section for common issues and their solutions.

7. Specifications

8. Warranty and Support

The TILSWALL Shark 800 HVLP Paint Sprayer comes with a 1-year warranty against manufacturing defects. If you encounter any quality problems with your paint sprayer within this period, please contact TILSWALL customer support for assistance.

For support, please refer to the contact information provided with your purchase or visit the official TILSWALL website. Our team is dedicated to finding a satisfactory solution for any issues you may experience.