Introduction
This manual provides detailed instructions for the UGREEN 20Gbps M.2 NVMe SATA SSD Enclosure, Model 55150. Please read this guide thoroughly before using the product to ensure proper installation, operation, and maintenance. This enclosure is designed to convert an M.2 NVMe or SATA SSD into a portable external storage device, offering high-speed data transfer and broad compatibility.
Image: UGREEN 20Gbps M.2 NVMe SATA SSD Enclosure with included USB-C cables.
Key Features:
- NVMe and SATA SSD Compatibility: Supports both PCIe NVMe and SATA NGFF SSDs up to 8TB in 2230, 2242, 2260, and 2280 sizes.
- 20Gbps Ultra-Fast Data Transfer: Achieves transfer speeds of up to 20Gbps with USB 3.2 Gen 2x2 ports.
- Efficient Heat Management: Features an aluminum case with a thermal pad for optimal heat dissipation.
- Secure & Stable Connection: Incorporates UASP and TRIM support, an RTL9220 chip, and protection against short-circuit and over-current.
- Easy Setup & Use: Plug-and-play design requiring no external power supply or drivers.
Setup and Installation
Follow these steps to install your M.2 SSD into the UGREEN enclosure:
- Open the Enclosure: Press the bottom of the enclosure and slide out the built-in black motherboard tray.
- Remove Screws: Locate and remove the small screws on the motherboard tray.
- Insert SSD: Carefully align your M.2 SSD with the slot on the motherboard tray and insert it. Ensure the SSD is fully seated.
- Secure SSD: Use the provided screw to fix the SSD in place with the fixed buckle.
- Apply Thermal Pad: Affix the silicone thermal pad onto the SSD. Ensure protective films are removed from both sides of the pad for effective heat transfer.
- Close Enclosure: Slide the motherboard tray back into the aluminum housing until it clicks securely into place.
Note: The SSD is not included with the enclosure.
Image: Step-by-step visual guide for M.2 SSD installation.
Operating Instructions
Connecting the Enclosure:
Connect the UGREEN SSD enclosure to your computer or compatible device using the provided USB-C to USB-C cable. The enclosure is plug-and-play, requiring no additional drivers for most operating systems.
Data Transfer:
For optimal performance, connect the enclosure to a USB 3.2 Gen 2x2 (20Gbps) port on your device. Other interfaces, such as Thunderbolt 4, will support speeds up to 10Gbps. The enclosure supports UASP (USB Attached SCSI Protocol) and TRIM commands for enhanced data transfer efficiency and SSD longevity.
Image: High-speed data transmission with UASP, showing 20Gbps capability.
Compatibility:
The enclosure is compatible with M.2 NVMe and SATA NGFF SSDs of sizes 2230, 2242, 2260, and 2280. It works with Windows, macOS, Linux, Android, and iOS systems. Please note that m-SATA SSDs are not supported.
Image: M.2 SSD compatibility chart for various sizes and key types.
Heat Management:
The aluminum casing and internal thermal pad are designed to dissipate heat effectively, maintaining optimal operating temperatures for your SSD and protecting data from overheating during prolonged use.
Image: Extreme heat dissipation features, including aluminum body and silicone pad.
Maintenance
To ensure the longevity and optimal performance of your UGREEN SSD enclosure, consider the following maintenance guidelines:
- Cleaning: Use a soft, dry cloth to clean the exterior of the enclosure. Avoid liquid cleaners or abrasive materials that could damage the finish.
- Handling: Handle the enclosure with care to prevent drops or impacts, which could damage the internal SSD or the enclosure itself.
- Storage: When not in use, store the enclosure in a cool, dry place away from direct sunlight and extreme temperatures.
- Disconnection: Always safely eject the device from your operating system before physically disconnecting it to prevent data corruption.
Troubleshooting
If you encounter issues with your UGREEN SSD enclosure, refer to the following common questions and solutions:
1. Why can't the enclosure reach 20Gbps?
This M.2 enclosure can only achieve up to 20Gbps transfer speeds when connected to a USB 3.2 Gen 2x2 (20Gbps) port. Other ports, including Thunderbolt 3 and Thunderbolt 4, are limited to a maximum of 10Gbps due to differences in data communication protocols. Ensure your host device's USB port supports USB 3.2 Gen 2x2 for maximum speeds.
2. Can this M.2 enclosure support 20Gbps with MacBook?
No, the enclosure will typically only reach 10Gbps on MacBooks. MacBooks generally feature Thunderbolt 3 or Thunderbolt 4 ports, which do not support 20Gbps when connected to this enclosure. The maximum speed will be limited by the Thunderbolt port's native USB compatibility, which is 10Gbps.
Image: Frequently Asked Questions regarding speed and MacBook compatibility.
Specifications
| Feature | Value |
|---|---|
| Brand | UGREEN |
| Model Number | 55150 |
| Item Weight | 0.11 Kilograms (3.87 ounces) |
| Memory Storage Capacity | Up to 8 TB |
| Compatible Devices | M.2 NVMe SSD, SATA SSD |
| Hard Disk Form Factor | 22 Millimeters (2230/2242/2260/2280) |
| Max Number of Supported Devices | 1 |
| Data Transfer Rate | 20 Gigabits Per Second (USB 3.2 Gen 2x2) |
| Hardware Interface | USB 3.2 Gen 2x2 |
| Color | Blue |
| Material | Aluminum |
| Hardware Platform | Universal |
Warranty and Support
UGREEN products are designed for reliability and performance. For specific warranty information, please refer to the warranty card included with your product or visit the official UGREEN website. For technical support, troubleshooting assistance, or any inquiries regarding your UGREEN 20Gbps M.2 NVMe SATA SSD Enclosure, please contact UGREEN customer service through their official channels.
No official product videos from the seller were found in the provided data for embedding in this manual.
