Moman HLS1 Solar Powered Helmet Safety Light User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Moman HLS1 Solar Powered Helmet Safety Light. Designed to enhance visibility and safety during night riding, in rain, or fog, this device features ultra-bright LED lights, solar charging capabilities, and an intelligent brake sensing system. Please read this manual thoroughly before use to ensure optimal performance and longevity of your device.

Product Overview

The Moman HLS1 is a compact and durable safety light designed for helmets. It integrates a solar panel for charging, bright LEDs for visibility, and a smart sensor for brake detection.

Package Contents:

• Moman HLS1 Helmet Light x 1
• User Manual x 1

Component Identification:

Figure 1: Moman HLS1 Component Diagram. Key components include the USB-C Port, Switch Button, Waterproof Rubber Pad, Adhesive Sticker, Solar Panel, and LED lights.

• Solar Panel: Located on the top surface, converts sunlight into electrical energy to charge the internal battery.
• LED Lights: Ultra-bright red LEDs for visibility and brake indication.
• USB-C Port: For alternative charging using a USB-C cable (not included).
• Switch Button: Controls power and operating modes.
• Waterproof Rubber Pad: Provides protection against water ingress.
• Adhesive Sticker: For secure attachment to the helmet.

Key Features

Enhanced Night Safety

Figure 2: Enhanced visibility with the Moman HLS1 light.

Equipped with ultra-bright LED lights, the Moman HLS1 significantly increases your visibility to other road users. This is crucial for riding at night, in rain, or fog, reducing accident risks and improving overall safety.

Solar-Powered & Energy-Saving

Figure 3: Solar charging and auto-brightness adaptation.

The high-efficiency solar panel ensures continuous charging under sunlight, minimizing the need for manual charging. A smart auto-brightness system adjusts light intensity based on ambient light, dimming in daylight and boosting visibility in darkness, promoting energy efficiency and environmental responsibility.

Auto-Sensing Brake Alert System

Figure 4: Automatic brake light activation.

This intelligent system detects deceleration and automatically switches the light from a flashing mode to a solid red light, clearly signaling your braking action to vehicles behind you. This feature operates without manual input, enhancing rear collision prevention.

Long Battery Life & Dual Charging

Figure 5: USB-C charging capability.

The built-in 500mAh rechargeable battery offers extended operation. In addition to solar charging, it supports rapid charging via a USB-C cable (not included). A full USB charge (approximately 5 hours) can provide up to 24 hours of continuous runtime.

Durable & Waterproof Design

Figure 6: IPX4 waterproof and drop-resistant construction.

Constructed from high-quality ABS plastic, the HLS1 is designed for impact resistance. With an IPX4 waterproof rating, it remains fully functional in rainy or wet conditions, ensuring reliability in various weather environments.

Easy Installation & Universal Fit

Figure 7: Wide compatibility with different helmet types.

The safety light is designed for universal compatibility with all helmet types. Installation is straightforward using the included adhesive strips, requiring no special tools for quick setup.

Setup and Installation

Follow these steps to properly install the Moman HLS1 on your helmet:

1. Prepare the Helmet Surface: Ensure the rear surface of your helmet where the light will be attached is clean, dry, and free of dust or grease.
2. Remove Protective Film: Carefully peel off the protective film from the adhesive sticker on the back of the helmet light. Note: The adhesive is very strong. For the first installation, a thin tool (like a knife edge) may be needed to help lift the sticker's edge.
3. Position the Light: Align the helmet light to the desired position on the rear of your helmet. Ensure it is centered and level for optimal visibility.
4. Apply Pressure: Once positioned, firmly press the helmet light onto the helmet surface for at least 30 seconds to ensure a strong bond.

Figure 8: Step-by-step installation guide.

The Moman HLS1 is designed for universal fit and can be attached to various helmet types, including motorcycle and bicycle helmets.

Operating Instructions

Power On/Off and Mode Selection:

• Power On: Press and hold the switch button for approximately 3 seconds until the lights illuminate.
• Power Off: Press and hold the switch button for approximately 3 seconds until the lights turn off.
• Cycle Modes: Briefly press the switch button to cycle through available lighting modes (e.g., flashing, solid).

Smart Sensing Functions:

Figure 9: Smart operational logic, including automatic brake light activation.

• Brake Mode: When significant deceleration is detected, the system automatically switches from Driving Mode (flashing) to Brake Mode (solid red light) to alert following vehicles.
• Driving Mode: When vibration is detected within 20 minutes of being in Standby Mode, the system automatically switches to Driving Mode. If no vibration is detected, it shuts down automatically.
• Standby Mode: If no motion is detected for 3 minutes while in Driving Mode, the system switches back to Standby Mode to conserve battery.
• Auto-Brightness: The light automatically adjusts its brightness based on ambient light conditions, dimming in bright environments and increasing intensity in low-light conditions.

Charging the Device:

The Moman HLS1 supports dual charging methods:

• Solar Charging: Place the helmet light in direct sunlight. The integrated solar panel will automatically charge the internal battery.
• USB-C Charging: For faster charging or when sunlight is unavailable, connect a USB-C cable (not included) to the USB-C port on the device and a compatible USB power source. A full charge typically takes about 5 hours and provides up to 24 hours of operation.

Maintenance

• Cleaning: Wipe the device with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the solar panel or casing. Ensure the solar panel is clean for efficient charging.
• Battery Care: To prolong battery life, avoid fully discharging the device frequently. If storing for an extended period, charge the device to at least 50% every few months.
• Storage: Store the helmet light in a cool, dry place away from direct sunlight when not in use for prolonged periods.

Troubleshooting

Specifications

Warranty and Support

The Moman HLS1 Solar Powered Helmet Safety Light comes with a 1-Year Manufacturer's Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.

What the Warranty Does Not Cover:

• Damage caused by misuse, abuse, accident, or neglect.
• Unauthorized repairs or modifications.
• Normal wear and tear.

Customer Support:

For warranty claims, technical assistance, or any questions regarding your Moman HLS1, please contact Moman customer support through the retailer where the product was purchased or visit the official Moman website for contact information.