upHere UP1 Series CPU Air Cooler Instruction Manual

1. Product Overview

The upHere UP1 Series CPU Air Cooler is designed to provide efficient cooling for your CPU. It features four 6mm copper heat pipes and a 120mm PWM fan, ensuring optimal thermal performance while maintaining quiet operation. This cooler is compatible with a wide range of Intel and AMD sockets, offering broad applicability for various PC builds.

Key Features:

• Universal Compatibility: Supports Intel LGA 1851/1700/1150/1155/1156/1200/1121/1366/1356/2011/2066 (X79/X99) and AMD AM5/AM4/AM3/AM2/FM2/FM1 series sockets.
• Exceptional Cooling Performance: Features four 6mm heat pipes for efficient heat dissipation and a direct heat pipe contact area of 25mm.
• Quiet Operation: Equipped with a 120mm fan operating at a maximum speed of 1650rpm ±10%, delivering 68.2CFM airflow with noise levels below 26dB(A).
• Easy Installation & RAM Clearance: Designed for non-disassembly fan installation and provides clearance for tall RAM modules.
• Versatile Power Connectivity: Utilizes a 4-pin power port and operates at 12V.

2. Package Contents

Please verify that all components are present before proceeding with installation:

• upHere UP1 Series CPU Air Cooler (Heatsink with 120mm Fan)
• Intel Mounting Kit (Backplate, brackets, screws)
• AMD Mounting Kit (Brackets, screws)
• Thermal Paste
• Thermal Paste Spatula
• User Guide

3. Installation Guide

Follow these steps carefully to install your upHere UP1 Series CPU Air Cooler. Ensure your system is powered off and unplugged before beginning.

3.1. Prepare the Motherboard

Depending on your CPU socket type (Intel or AMD), select the appropriate mounting hardware.

For Intel Sockets (LGA 1851/1700/1150/1155/1156/1200/1121/1366/1356/2011/2066):

1. Attach the universal backplate to the rear of the motherboard, aligning the holes with the CPU socket. Adjust the backplate clips for your specific socket type (e.g., 115X/1200, 1700, 1366).
2. Secure the Intel mounting brackets to the front of the motherboard using the provided screws. Tighten them evenly.

For AMD Sockets (AM5/AM4/AM3/AM2/FM2/FM1):

1. Remove the existing plastic retention modules from the motherboard, but retain the original AMD backplate.
2. Install the AMD mounting brackets onto the motherboard, aligning them with the backplate screw holes. Secure them with the provided screws.

3.2. Apply Thermal Paste

Apply a small amount of thermal paste (pea-sized dot) to the center of your CPU's integrated heat spreader (IHS). Use the provided spatula to spread it evenly into a thin layer across the entire surface of the IHS.

Image: The cooler features four pure copper direct contact heat pipes designed to efficiently transfer heat from the CPU.

3.3. Mount the CPU Cooler

1. Remove the protective film from the cooler's base.
2. Carefully place the CPU cooler onto the CPU, aligning the mounting holes on the cooler with the standoffs or brackets on the motherboard.
3. Using a screwdriver, tighten the screws on the cooler in a diagonal pattern (e.g., top-left, bottom-right, top-right, bottom-left) until snug. Do not overtighten.

Image: The cooler is designed for easy installation from above, without needing to remove the fan.

3.4. Connect the Fan Cable

Locate the 4-pin CPU fan header on your motherboard (usually labeled 'CPU_FAN' or similar). Connect the cooler's 4-pin PWM cable to this header.

Image: The 4-pin power connector ensures compatibility with various motherboard configurations.

4. Operating Instructions

Once installed, the upHere UP1 Series CPU Air Cooler operates automatically based on your motherboard's fan control settings. The 4-pin PWM connection allows the motherboard to dynamically adjust the fan speed according to CPU temperature, optimizing for both cooling performance and noise levels.

Fan Speed and Noise:

• The 120mm fan operates within a speed range of 600-1650 RPM ±10%.
• At maximum speed, the fan delivers an airflow of 68.2 CFM.
• Noise levels are kept below 26 dB(A) for quiet operation.

Image: Performance specifications of the PWM fan, highlighting quiet and efficient cooling.

5. Maintenance

Regular maintenance ensures optimal performance and longevity of your CPU cooler.

• Dust Removal: Periodically clean the heatsink fins and fan blades to prevent dust buildup, which can impede airflow and reduce cooling efficiency. Use compressed air or a soft brush.
• Thermal Paste: Reapply thermal paste if you remove the cooler for any reason, or if you notice a significant increase in CPU temperatures over time.
• Fan Inspection: Check the fan for any unusual noises or wobbling. If the fan is damaged or excessively noisy, consider replacing it.

6. Troubleshooting

If you encounter issues with your CPU cooler, refer to the following common troubleshooting steps:

• Fan Not Spinning: Ensure the 4-pin PWM cable is securely connected to the CPU_FAN header on the motherboard. Check BIOS/UEFI settings to confirm fan control is enabled and configured correctly.
• High CPU Temperatures: Verify that the cooler is properly seated on the CPU and that the mounting screws are tightened evenly. Ensure sufficient thermal paste was applied. Check for adequate airflow within your PC case.
• Excessive Noise: Confirm that the fan blades are free from obstructions. Check if the fan is securely mounted and not vibrating against other components. Adjust fan speed settings in BIOS/UEFI if necessary.
• Compatibility Issues: Double-check that your motherboard socket is listed as compatible with this cooler.

If problems persist, contact upHere customer support for further assistance.

7. Specifications

Detailed technical specifications for the upHere UP1 Series CPU Air Cooler:

Image: Detailed technical specifications and physical dimensions of the cooler.

8. Warranty and Support

upHere products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the official upHere website or contact their customer service department.

Please retain your proof of purchase for warranty claims.