Avisontek GK-R Wireless Genie Garage Door Opener Keypad Replacement Manual

1. Introduction

The Avisontek GK-R Wireless Keypad provides convenient keyless entry for your garage. This manual offers detailed instructions for installation, programming, operation, and maintenance to ensure optimal performance and security.

Please read this manual thoroughly before attempting to install or program your new keypad.

2. Compatibility

The Avisontek GK-R Wireless Keypad is designed for compatibility with:

• All Genie garage door openers manufactured from 1995 to present.
• It can also replace older model Genie Intellicode Keypads such as GWKP, GWK-IC, ACSDG, ACSDA1, ACSD1G, BRQACSDA, BRQACSDA1, equivalent to 37332R, GK-BX.

Important Note:

• This keypad is NOT compatible with DIP switch openers (Genie from 1982 to 1996 and Overhead Door from 1995 to 1996).

Image: Compatibility chart for Avisontek GK-R keypad.

3. Features

• Rolling Code Security: Generates a new access code with each use to prevent code interception and enhance security.
• Keyless Entry: Allows access without physical keys or handheld remotes.
• Wireless DIY Installation: No complex wiring required. Includes mounting screws for easy setup.
• Weatherproof Design: Features a flip protective cover to shield the keypad from rain, snow, and sunlight.
• Backlit Buttons: Provides clear visibility for code input, even at night.
• Dual Frequency: Operates on both 315MHz and 390MHz frequencies with auto-seek technology.
• Temporary Passcode: Create temporary access codes for maintenance staff or visitors.

Image: Industrial-grade chip and rolling code encryption for enhanced security.

Image: Keypad demonstrating cold and shock resistance, and weatherproof design.

4. Setup and Programming

4.1. Wireless Installation

The GK-R keypad is designed for easy wireless installation. No complex wiring is needed. Simply mount the keypad to a desired location near your garage door using the included screws. The keypad comes with preloaded AAA batteries.

4.2. Programming Your Personal Identification Number (PIN)

Follow these steps to set your personal 3-8 digit PIN on the keypad:

1. Confirm that the keypad backlight is off. Do not press any buttons.
2. Press 3, then 5, then 7 on the keypad. Then press the PROGRAM button.
3. The LED will blink. Now, enter your unique 3-8 digit PIN number.
4. Press the PROGRAM button again.
5. The keypad LED will blink twice and then shut off, confirming successful PIN programming.

4.3. Syncing the Keypad with Your Garage Door Opener

After setting your PIN, sync the keypad with your garage door opener. Refer to your garage door opener's manual for specific programming mode instructions, or use the general steps below:

1. Enter programming mode on your garage door opener. This usually involves pressing and holding a program button or pressing a learn code button. The LED on the opener will typically illuminate or flash.
2. Confirm that the keypad backlight is off. Do not press any buttons.
3. Enter your newly programmed PIN (from step 4.2) into the keypad.
4. Press the UP or Down arrow key on the keypad 3-4 times until the garage door opener activates, confirming successful programming.

Image: Detailed programming instructions for the Avisontek GK-R keypad.

Play video

Video: Programming instructions for the Avisontek GK-R Wireless Keypad. This video demonstrates the steps to program the keypad with a Genie garage door opener.

5. Operating Instructions

To operate your garage door using the Avisontek GK-R Wireless Keypad:

1. Ensure the keypad cover is open.
2. Enter your personal 3-8 digit PIN code.
3. Press the UP or Down arrow key. The garage door will activate.

For temporary access, you can create a temporary passcode. This allows maintenance personnel or visitors to open your garage without knowing your primary PIN. Consult the keypad's internal instructions for temporary passcode setup.

Image: One-touch operation of the Avisontek GK-R keypad.

6. Maintenance

6.1. Battery Replacement

The keypad is powered by two AAA alkaline batteries, which are preloaded. When the keypad's backlight becomes dim or the keypad stops responding, it is time to replace the batteries.

1. Open the battery compartment located at the bottom of the keypad.
2. Remove the old AAA batteries.
3. Insert two new standard AAA alkaline batteries, ensuring correct polarity.
4. Close the battery compartment securely.

Image: Battery compartment and AAA alkaline battery information.

7. Troubleshooting

If you encounter issues with your Avisontek GK-R Wireless Keypad, consider the following:

• Keypad Not Responding: Check if the batteries need replacement. Ensure they are inserted with correct polarity.
• Programming Issues: Carefully re-read the programming steps in Section 4. If problems persist, watch the provided programming video again. Ensure your garage door opener is in programming mode correctly.
• Door Not Opening/Closing: Verify that the keypad is within the effective range of 164 feet from your garage door opener. Confirm that your garage door opener is compatible with the GK-R keypad (refer to Section 2).
• Incorrect Code Entry: Ensure you are entering the correct 3-8 digit PIN. The backlit buttons should help with visibility.

If these steps do not resolve the issue, please contact Avisontek customer support for further assistance.

8. Specifications

Image: Product specifications and dimensions for the Avisontek GK-R keypad.

9. Warranty and Support

The Avisontek GK-R Wireless Keypad comes with a 3-year quality warranty. It is officially FCC certified, ensuring compliance with US electronic safety standards.

For any questions, technical assistance, or warranty claims, please contact Avisontek customer service. 24-hour Amazon online tech support is also available.

Image: Warranty and support information.