VEVOR Gravity Water Filter System K8626 Instruction Manual

1. Introduction

This manual provides essential instructions for the safe and efficient use of your VEVOR Gravity Water Filter System, Model K8626. This system is designed to provide clean drinking water by filtering out impurities using gravity, without the need for electricity. It is suitable for both indoor and outdoor use, including camping, fishing, hiking, and emergency situations.

Please read this manual thoroughly before assembly and operation to ensure proper function and longevity of your product. Keep this manual for future reference.

2. Safety Information

• Always use clean water sources for filtration. The system is designed to filter potable water, not to purify highly contaminated water without prior treatment.
• Do not use hot water with the filter system, as this can damage the filter elements and the stainless steel components.
• Ensure all components are securely assembled before filling the system with water to prevent leaks.
• Keep the system out of reach of children to prevent accidental spills or damage.
• Regularly inspect the filter elements and the system for any signs of wear or damage. Replace filters as recommended.
• Do not use abrasive cleaners or harsh chemicals on the stainless steel components, as this can damage the finish.

3. Package Contents

Verify that all items listed below are included in your package:

• Gravity Water Filtration System (Upper and Lower Chambers)
• Activated Carbon Filter Cartridges (x2)
• Upper Lid Handle (x1)
• Plugs for filter holes (x2)
• Stainless Steel Faucet (x1)
• Screwdriver (x1)
• Open-end Wrench (x1)
• Faucet Gaskets (x2)
• Faucet Sealing Rings (milky white) (x2)
• Sealing Gasket for Filter Cleaning (yellow) (x1)
• Filter Cartridge Instruction Manual (x1)
• Rubber Foot Pad for the bottom of the bucket (x1)

Figure 1: Included components and product parameters. This image illustrates the various parts that come with the VEVOR Gravity Water Filter System, including the upper and lower chambers, filter cartridges, faucet, and other accessories, along with key dimensions.

4. Setup and Assembly

Follow these steps to assemble your VEVOR Gravity Water Filter System:

4.1. Prepare Filter Cartridges

1. Unpack the two activated carbon filter cartridges.
2. Rinse the filters under cold running water for several minutes to remove any loose carbon dust.
3. Priming the filters: Place the yellow sealing gasket onto the threaded stem of a filter. Press the filter stem against a faucet to allow water to flow through the filter until water drips from the other end. Repeat for the second filter. This ensures proper water flow and removes air from the filter media.

4.2. Assemble the Faucet

1. Locate the faucet hole on the lower chamber.
2. Insert one faucet gasket onto the threaded stem of the faucet.
3. Insert the faucet stem through the hole from the outside of the lower chamber.
4. From the inside of the lower chamber, place the second faucet gasket and then a milky white sealing ring onto the faucet stem.
5. Secure the faucet with the provided nut, tightening it with the open-end wrench until snug. Do not overtighten.

4.3. Install Filter Cartridges

1. Place the upper chamber onto a stable surface.
2. Insert the threaded stems of the prepared filter cartridges into the two holes at the bottom of the upper chamber.
3. From inside the upper chamber, secure each filter with a milky white sealing ring and then a wing nut (if provided, otherwise use the standard nut and screwdriver). Tighten until snug, ensuring a watertight seal. Do not overtighten.

Figure 2: Easy installation and component identification. This image highlights the key parts of the system and how they fit together, including the activated carbon filters, stainless steel chambers, and the faucet.

4.4. Final Assembly

1. Place the rubber foot pad on the bottom of the lower chamber for stability.
2. Carefully place the upper chamber (with filters installed) onto the lower chamber.
3. Place the lid with the handle on top of the upper chamber.

Figure 3: Fully assembled VEVOR Gravity Water Filter System, ready for use.

Figure 4: The system's compact design allows the upper chamber to nest inside the lower chamber for easy transport and storage.

5. Operation

5.1. Initial Use (Flushing)

1. After assembly, fill the upper chamber with clean water.
2. Allow the water to filter through to the lower chamber. The first batch of filtered water may contain residual carbon dust and should be discarded.
3. Repeat this process 1-2 times, discarding the filtered water, until the water runs clear and tastes clean. This flushes the filters and prepares the system for regular use.

5.2. Daily Use

1. Pour water into the upper chamber. The water will slowly pass through the filter cartridges by gravity into the lower chamber.
2. Once the water has filtered, open the faucet on the lower chamber to dispense clean drinking water.
3. Refill the upper chamber as needed.

Figure 5: Filtration efficiency of the activated carbon filters, demonstrating removal of various contaminants.

6. Maintenance

6.1. Cleaning the System

• Regularly clean the stainless steel chambers with warm, soapy water and a soft cloth. Rinse thoroughly.
• For thorough cleaning, disassemble the chambers and faucet.
• Do not use abrasive pads or harsh chemicals, as these can scratch or damage the stainless steel.

Figure 6: The seamless SUS304 food-grade stainless steel construction ensures durability, resistance to corrosion, and ease of cleaning.

6.2. Filter Replacement

• The activated carbon filter cartridges have a lifespan of up to 6,000 gallons (approximately 22,700 liters) per pair, depending on water quality and usage.
• Replace filters when you notice a significant decrease in flow rate or a change in water taste or odor.
• To replace filters, empty the system, remove the upper chamber, and unscrew the old filter cartridges.
• Install new, primed filter cartridges following the steps in Section 4.3.
• Perform the initial flushing procedure (Section 5.1) after replacing filters.

Figure 7: Each pair of filters provides sustainable filtration for up to 6,000 gallons (approximately 22,700 liters) of water.

7. Troubleshooting

8. Specifications

9. Warranty and Support

For warranty information or technical support, please contact VEVOR customer service through their official website or the retailer from whom you purchased the product. Please have your model number (K8626) and purchase details ready when contacting support.