Evenflo Revolve360 Extend All-in-One Rotational Car Seat Instruction Manual

Introduction

The Evenflo Revolve360 Extend All-in-One Rotational Car Seat is designed to provide safety and convenience for your child through various growth stages. This car seat offers extended rear-facing capabilities, transitions to forward-facing, and converts into a booster seat, accommodating children from 4 to 120 lbs. Its innovative 360-degree rotation feature simplifies placing and removing your child from the vehicle.

This manual provides essential information for proper installation, operation, maintenance, and troubleshooting to ensure the safe and effective use of your Evenflo Revolve360 Extend car seat.

Safety Information

Always read and understand all instructions and warnings in this manual and on the car seat itself before use. Failure to follow these instructions could result in serious injury or death.

• Ensure the car seat is correctly installed and secured in your vehicle according to the instructions.
• Always secure your child in the harness system, ensuring straps are snug and the chest clip is at armpit level.
• Never leave your child unattended in the car seat.
• Do not use accessories or parts not approved by Evenflo.
• The Evenflo Revolve360 Extend meets or exceeds all applicable federal safety standards, including side-impact and rollover testing.

Setup

Installation

The Evenflo Revolve360 Extend features the Sure360™ Safety Installation System with LockStrong™ and Tether360™ for a secure, one-time installation. A bead-level indicator assists in achieving proper leveling.

1. Place the car seat base firmly on the vehicle seat.
2. Attach the lower connectors (LATCH) to your vehicle's lower anchors.
3. Engage the LockStrong™ arm to tighten the installation, ensuring the car seat is secure and does not move more than 1 inch side-to-side or front-to-back at the belt path.
4. For forward-facing, attach the Tether360™ strap to the vehicle's top tether anchor and tighten.
5. Verify the bead-level indicator shows the correct recline angle for your child's mode.

Harness and Headrest Adjustment

The car seat features a no-rethread harness with 14 adjustable positions, allowing the harness and headrest to grow with your child without manual re-threading.

• To adjust, locate the adjustment lever at the top of the headrest.
• Squeeze the lever and slide the headrest up or down to the desired position.
• Ensure the shoulder straps are at or just below the child's shoulders for rear-facing, and at or just above the child's shoulders for forward-facing.

Leg Rest Attachment

A zip-on, ergonomic leg rest is included to provide additional comfort for growing legs.

• Locate the zipper around the front edge of the car seat's base.
• Align the leg rest with the zipper and securely attach it.
• The leg rest can be reversed for different comfort preferences.

Operating

360-Degree Rotation

The car seat features a one-hand, 360-degree rotation mechanism, making it easy to get your child in and out of the car from either side.

• To rotate the seat, lift the rotation lever located at the front of the seat.
• Rotate the seat towards the car door to easily place or remove your child.
• Once your child is secured, rotate the seat back to the desired rear-facing or forward-facing position until it clicks and the lock indicator shows green.

Usage Modes

The Evenflo Revolve360 Extend offers three modes of use to adapt to your child's growth:

• Rear-Facing Mode: For children weighing 4 to 50 lbs. Child safety experts recommend keeping children rear-facing as long as possible.
• Forward-Facing Mode: For children weighing 22 to 65 lbs.
• Booster Mode: For children weighing 40 to 120 lbs.

On-the-Go Recline

The car seat allows for easy recline adjustments without needing to reinstall the seat or disturb your child.

• Locate the recline adjustment handle, typically at the front or side of the seat.
• Squeeze the handle and adjust the seat to one of the 6 available recline positions.
• Ensure the recline position is appropriate for your child's age, weight, and mode of use.

Product Overview Video

Maintenance

Quick Clean Cover

The Quick Clean Cover is designed for easy removal and washing, simplifying maintenance.

• To remove the cover, unzip it from the car seat frame.
• Machine wash the seat pad separately in cold water on a delicate cycle.
• Tumble dry for 10 to 15 minutes on low heat.
• Reattach the cover by zipping it back onto the car seat frame.

General Cleaning

• DO NOT lubricate or immerse in water any part of this child restraint, unless rinsing is permitted.
• Plastic and metal parts may be wiped clean with mild soap and water and dried with a soft cloth.
• The harness can be wiped clean with mild soap and water. Allow harness to air dry.

Troubleshooting

If you encounter any issues with your Evenflo Revolve360 Extend car seat, please refer to the detailed troubleshooting section in the full product manual or contact customer support.

• Installation Issues: Ensure all LATCH connectors and tethers are correctly attached and tightened. Check the bead-level indicator for proper recline.
• Harness Adjustment: Verify the no-rethread harness is moving freely and is not twisted. Ensure the adjustment lever is fully engaged.
• Rotation Mechanism: Confirm the rotation lever is fully lifted before attempting to rotate the seat. Ensure no obstructions are preventing movement.

Specifications

Support

ParentLink® Customer Service

Evenflo offers ParentLink® customer service experts to assist with product inquiries and installation support.

• Access online chat support for real-time assistance.
• Receive live video support with a certified car seat safety technician for proper vehicle installation guidance.

For further assistance, please visit the Evenflo Store or refer to the full product manual.