Mcbazel MT-led-060062

Mcbazel Wireless Rechargeable Magnetic LED Strobe Lights

Model: MT-led-060062

Introduction

This manual provides detailed instructions for the safe and effective use of your Mcbazel Wireless Rechargeable Magnetic LED Strobe Lights. These versatile lights are designed for various applications, including vehicles, outdoor activities, and emergency signaling. Please read this manual thoroughly before first use and retain it for future reference.

Package Contents

Verify that all items listed below are included in your package:

  • 4 x LED Strobe Lights
  • 1 x Remote Controller
  • 4 x Hook and Loop Stickers
  • 8 x Rubber Rings
  • 2 x USB Charging Cables
  • 1 x User Manual
Image showing the package contents including four LED strobe lights, a remote control, hook and loop stickers, rubber bands, charging cables, and a user manual.
Figure 1: Package Contents. This image displays all components included in the product package.

Setup

First Time Use Activation

  1. Remove the transparent film from the remote control before use.
  2. Charge each light for 5 seconds using the provided USB charging cable, then unplug the cable.
  3. Within 1 minute after unplugging, press and hold the "ON" button on the remote control for 2-3 seconds to activate the device.

Important: Do not use fast-charging adapters. Only standard 5V 1A adapters are permitted for charging.

Diagram illustrating the three steps for first-time activation: removing remote film, charging lights for 5 seconds, and long-pressing the ON button on the remote.
Figure 2: First Time Use Activation Steps. This diagram visually guides users through the initial setup process.

Installation Methods

The LED strobe lights offer flexible installation options:

  • Magnetic Attachment: Each light features a strong magnet for easy attachment to any metal surface.
  • Hook and Loop Stickers: For non-metallic surfaces, use the provided hook and loop stickers. Tear off one sticker, paste it to the light, and paste another to your desired installation location.
  • Rubber Bands: Utilize the rubber rings to secure the lights around bars or irregular shapes. Tie the band into the light groove, then tie it to the groove on the other side, and fix the strobe light in place.
Diagram showing installation using hook and loop stickers: peeling, attaching to light, and attaching to surface.
Figure 3: Hook and Loop Installation. This image demonstrates how to use the hook and loop stickers for secure mounting.
Diagram showing installation using rubber bands: threading through light, securing to groove, and fixing to installation location.
Figure 4: Rubber Band Installation. This image illustrates the process of attaching the lights using rubber bands.

Video 1: How to Use the Product. This video demonstrates the basic usage and installation of the strobe lights.

Operating Instructions

Remote Control Functions

The included slim remote control allows for easy adjustment of light settings from a distance (within 8 meters). You can switch colors, change modes, or power the lights on/off with a single click.

Image showing the remote control with various color and mode buttons, and two LED strobe lights in the foreground.
Figure 5: Wireless Remote Control. This image highlights the remote control and its functionality for changing light settings.

Color and Mode Selection

The lights feature 8 distinct colors (White, Yellow, Ice Blue, Red, Green, Purple, Pink, Blue) and multiple lighting modes. Use the remote to cycle through these options to suit your preference or application.

Image displaying a motorcycle with multiple colored LED strobe lights, and a row of individual lights showing each of the 8 available colors.
Figure 6: 8 Light Colors & Multi-Modes. This image demonstrates the range of colors and dynamic lighting effects.

Syncing Multiple Lights

To ensure all 4 units receive the signal simultaneously and operate in sync, press and hold the "ON" button on the remote for 2-3 seconds. A short click may only activate 1-2 units.

Diagram illustrating the difference between a short click and a long press on the remote for syncing lights. A short click shows only 1-2 lights activating, while a long press shows all 4 lights activating in sync.
Figure 7: Syncing All 4 Lights. This image clarifies the correct method for synchronizing multiple lights.

Video 2: Sync All 4 Lights with One Click! This video demonstrates the process of syncing multiple lights using the remote control.

Maintenance

Charging the Lights

The lights feature a built-in 110mAh rechargeable lithium battery. A single full charge can provide up to 12 hours of illumination. Actual battery life varies based on the selected color mode and brightness level:

  • High Brightness Mode: Approximately 2-7 hours (applies to white/red/green/blue/yellow/purple/pink/ice blue/8-color auto-cycle).
  • Medium Brightness Mode: Approximately 4-14 hours.
  • Low Brightness Mode: Approximately 8-28 hours.

The remote control enters sleep mode after 60 seconds of inactivity to conserve power.

Chart showing multi-mode runtime reference for high, medium, and low brightness modes, with approximate battery life ranges.
Figure 8: Multi-Mode Runtime Reference. This chart provides estimated battery life based on brightness settings.

Cleaning

To clean the lights, gently wipe them with a soft, damp cloth. Do not use abrasive cleaners or solvents.

Troubleshooting

ProblemSolution
Strobe light does not turn on via remote control.Press and hold the "OFF" button on the remote for 10 seconds to perform a reset. A successful reset is confirmed when the device remains off and does not respond after pressing the "ON" button. After a successful reset, press and hold the "ON" button for 2-3 seconds to activate the light.
One of the lights is not illuminating.Try charging the light again for a few minutes, then unplugging and reconnecting the charging cable. This can help to reset the light.
Lights are not syncing properly.Ensure you are pressing and holding the "ON" button on the remote for 2-3 seconds to sync all units simultaneously. A short click may only activate individual units.
Image showing a person on a motorcycle at dusk, with a hand holding the remote control. Text overlays describe troubleshooting steps for the strobe lights.
Figure 9: Troubleshooting Guide. This image provides visual context for common issues and their solutions.

Specifications

FeatureDetail
BrandMcbazel
Model NumberMT-led-060062
Item Dimensions (L x W x H)5.91 x 4.45 x 0.71 inches
Item Weight67 Grams
ColorMulticolor (8 colors)
Light Source TypeLED
Voltage5 Volts (DC)
Connectivity TechnologyUSB
Water Resistance LevelWaterproof
Includes RemoteYes
Battery Capacity110mAh rechargeable lithium battery
Fit TypeUniversal Fit
Material TypeComposite

Warranty and Support

Specific warranty information for this product is not provided in the available data. For warranty details or technical support, please contact Mcbazel customer service directly through their official website or the retailer where the product was purchased.

Related Documents - MT-led-060062

Preview Mcbazel MT-A Automatic Watch Winder User Manual
Comprehensive user manual for the Mcbazel MT-A Automatic Watch Winder. Includes setup instructions, power requirements, operating modes, and maintenance tips.
Preview Yamaha Motorcycle Turn Signal Installation and Safety Guide
Comprehensive instructions for installing and using Yamaha motorcycle turn signals, including safety warnings, precautions, and FAQs. Ensure proper fitment for models like MT-07, MT-09, and others.
Preview Lenovo ThinkPad X200/X201 Series Hardware Maintenance Manual
Detailed hardware maintenance and service manual for Lenovo ThinkPad X200, X200s, X200si, X201, X201i, and X201s series laptops, covering component identification, removal, replacement, and troubleshooting.
Preview Danfoss Maneurop MT & MTZ Reciprocating Compressors: Application Guide
Comprehensive application guide for Danfoss Maneurop MT and MTZ series reciprocating compressors. Covers product details, technical specifications, performance data, installation, and service for refrigeration and air conditioning applications.
Preview SWIFT Standards MT: Category 9 - Cash Management and Customer Status Message Reference Guide (November 2021)
This comprehensive guide details SWIFT's Category 9 message types for Cash Management and Customer Status, covering message scope, format specifications, rules, and examples for Standards MT November 2021. Essential for financial institutions.
Preview Hilti MT-ZT Installation Instructions (M8/M10/3/8")
Official installation guide for Hilti MT-ZT mounting components. Includes assembly steps, torque specifications, and compatibility details for M8, M10, and 3/8" threaded rods.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.