1. Introduction
The LILYGO T-Embed CC1101 ESP32-S3 TTGO Development Board is a compact, low-power wireless module featuring a 1.9-inch IPS TFT LCD and a transparent shell. It is designed for various development and experimental applications, integrating an ESP32-S3 dual-core LX7 microprocessor and a CC1101 Sub-1 GHz RF transceiver.
This manual provides essential information for setting up, operating, maintaining, and troubleshooting your T-Embed CC1101 device.

Figure 1.1: Front view of the LILYGO T-Embed CC1101 Development Board with its transparent shell, displaying the 1.9-inch IPS TFT LCD.
2. Setup and Initial Configuration
The LILYGO T-Embed CC1101 comes with a user manual in the box. For initial setup and advanced configurations, it is recommended to refer to the official GitHub repository for the latest firmware and development resources.
- Power Supply: The device supports dual power supply via USB or the built-in 1300mAh Li-Po battery (included). Connect the device to a USB power source using a compatible cable for charging and initial power-on.
- Firmware Installation: For custom applications or updates, firmware can be flashed to the device. Detailed instructions and necessary tools are available on the official GitHub page: github.com/Xinyuan-LilyGO/T-Embed-CC1101.
- Microphone Note: If a CC1101 expansion board is added to the embedded system, the microphone functionality will be disabled. This is due to the hardware design and cannot be altered.

Figure 2.1: View of the LILYGO T-Embed CC1101, highlighting the internal battery and transparent casing.
3. Operation
The T-Embed CC1101 is equipped with an ESP32-S3 dual-core LX7 microprocessor, providing robust processing capabilities for various tasks. Its intuitive user interface and tactile buttons facilitate ease of use.
3.1 Key Features and Components
- Display: Features a 1.9-inch ST7789V IPS TFT LCD with a resolution of 170(H)RGB x 320(V) pixels for clear visual feedback.
- Wireless Connectivity: Supports Wi-Fi 802.11 b/g/n and BLE5 for versatile wireless communication.
- RF Transceiver: Includes a CC1101 Low-Power Sub-1 GHz RF Transceiver, operating on frequency bands 300-348MHz, 387-464MHz, and 779-928MHz.
- NFC/RFID: Integrated PN532 NFC/RFID I2C transceiver module for near-field communication applications.
- Onboard Functions: Provides Reset and Boot buttons, along with IR Transmit & Receive capabilities.

Figure 3.1: Technical diagram illustrating the main components and features of the LILYGO T-Embed CC1101.
3.2 Basic Usage
Once powered on and with appropriate firmware loaded, the device's functions can be accessed via the integrated display and control buttons. Refer to your specific firmware's documentation for detailed operational procedures.

Figure 3.2: Side-by-side view of the LILYGO T-Embed CC1101, showing both the front with the display and controls, and the back.
4. Maintenance
Proper maintenance ensures the longevity and optimal performance of your LILYGO T-Embed CC1101.
- Cleaning: Use a soft, dry cloth to clean the device. Avoid using liquid cleaners or abrasive materials, which can damage the screen or casing.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: The device contains a Lithium Polymer battery. Avoid fully discharging the battery frequently. For long-term storage, charge the battery to approximately 50% to preserve its lifespan.
- Firmware Updates: Regularly check the official GitHub repository for firmware updates. Updates can improve performance, add new features, and resolve bugs.
5. Troubleshooting
This section addresses common issues you might encounter with your LILYGO T-Embed CC1101.
| Problem | Possible Cause | Solution |
|---|---|---|
| Screen displays only backlight, no image. | Firmware issue, display driver issue, or hardware malfunction. |
|
| Device does not power on. | Low battery or power connection issue. |
|
| Wireless connectivity issues (Wi-Fi/BLE). | Firmware configuration or environmental interference. |
|
6. Specifications
Detailed technical specifications for the LILYGO T-Embed CC1101 ESP32-S3 TTGO Development Board:
| Feature | Detail |
|---|---|
| MCU | ESP32-S3 Dual-core LX7 microprocessor |
| Wireless Connectivity | Wi-Fi 802.11 b/g/n, BLE5 |
| RF Transceiver | CC1101 Low-Power Sub-1 GHz (300-348MHz, 387-464MHz, 779-928MHz) |
| NFC/RFID | PN532 I2C transceiver module |
| Display | 1.9-inch IPS TFT LCD (ST7789V), 170(H)RGB x 320(V) resolution |
| Flash Memory | 16 MB |
| RAM | LPDDR4X |
| Operating System | Linux (firmware dependent) |
| Power Supply | USB / Li-Po Battery (1300mAh included) |
| Item Weight | 4.6 ounces |
| Package Dimensions | 6.38 x 6.34 x 1.85 inches |
| Color | Transparent Shell |

Figure 6.1: Dimensions of the LILYGO T-Embed CC1101 device.

Figure 6.2: LILYGO T-Embed CC1101 Pinmap diagram, showing various I/O pins and components.
7. Warranty and Support
LILYGO is committed to providing quality products and customer service.
- Product Service: If you have any questions or require assistance with your LILYGO T-Embed CC1101, please contact LILYGO customer service. They aim to answer your questions as soon as possible.
- Warranty Information: Specific warranty terms and conditions may vary. Please refer to the product packaging or contact LILYGO directly for detailed warranty information.
- Online Resources: For the most up-to-date information, firmware, and community support, visit the official LILYGO GitHub repository: github.com/Xinyuan-LilyGO/T-Embed-CC1101.