ALLIMITY RC-157

Download PDFFree PDF. The Save button below keeps a bookmark and private notes in your account.

Instruction Manual

ALLIMITY RC-157 Replacement Remote Control

Model: RC-157

Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your new ALLIMITY RC-157 Replacement Remote Control. This remote is specifically designed to be compatible with Sherwood AV Receivers RX-4208, RX-4508, RX4208, and RX4508.

Please read this manual thoroughly before using the remote control to ensure proper functionality and to avoid any issues.

Product Overview

The ALLIMITY RC-157 is an infrared (IR) replacement remote control. It requires no programming or pairing. Simply insert batteries, and it is ready for use with compatible Sherwood AV receivers.

Figure 1: Front view of the ALLIMITY RC-157 Replacement Remote Control, showing all buttons and layout.

Figure 2: Angled view of the ALLIMITY RC-157 Replacement Remote Control, highlighting its ergonomic design.

Side and front view with dimensions of the ALLIMITY RC-157 Replacement Remote Control

Figure 3: Side and front view of the ALLIMITY RC-157 Replacement Remote Control, illustrating its dimensions (approximately 21 cm / 8.27 inches long and 5 cm / 1.97 inches wide).

Setup

The RC-157 remote control requires two AAA alkaline batteries (not included) for operation.

Locate the Battery Compartment: Turn the remote control over. The battery compartment is located on the back.

Back view of the ALLIMITY RC-157 Replacement Remote Control with battery cover removed

Figure 4: Back view of the remote control with the battery cover removed, showing the battery slots.

Open the Battery Cover: Slide the battery cover downwards or press the latch and lift to open the compartment.
Insert Batteries: Insert two new AAA alkaline batteries into the compartment, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
Close the Battery Cover: Replace the battery cover by sliding it back into place until it clicks securely.

Important Notice:

Ensure there is nothing blocking the path between your AV receiver and the remote control for optimal performance.
This is an IR remote control and does not require any programming or pairing with your Sherwood AV receiver.

Operating Instructions

Once batteries are installed, the remote control is ready for immediate use with compatible Sherwood AV Receivers (RX-4208, RX-4508, RX4208, RX4508).

Key Functions:

Button	Function
POWER	Turns the AV receiver On or Off.
Number Buttons (0-9)	Direct input for channel selection or other numerical functions.
CD, AUX, PHONO, TUNER	Selects the corresponding audio input source.
VOLUME (+/-)	Adjusts the master volume level.
MUTE	Mutes or unmutes the audio output.
Navigation Arrows (Up, Down, Left, Right)	Navigates menus and selections.
MEMO/ENTER	Confirms selections or stores settings.
PRESET	Accesses or cycles through radio presets.
BASS (+/-)	Adjusts the bass level.
TREBLE (+/-)	Adjusts the treble level.
BALANCE (L/R)	Adjusts the audio balance between left and right channels.
DISPLAY	Cycles through display modes or information on the receiver.
SEARCH MODE	Initiates or changes search modes for tuner or media.
Bt (Bluetooth)	Selects Bluetooth input (if supported by receiver).
MO/ST	Mono/Stereo toggle for radio.
SLEEP	Activates or adjusts the sleep timer.
DIMMER	Adjusts the brightness of the receiver's display.
SPEAKER (A/B)	Selects speaker output A, B, or A+B.
TONE DIRECT	Bypasses tone controls for a direct audio path.

Maintenance

Cleaning: Use a soft, dry cloth to clean the remote control. Do not use liquid cleaners or abrasive materials, as they may damage the surface or internal components.
Battery Replacement: Replace batteries when the remote's responsiveness decreases or it stops functioning. Always replace both batteries at the same time with new alkaline batteries.
Storage: If the remote control will not be used for an extended period, remove the batteries to prevent leakage and potential damage to the remote. Store in a cool, dry place.
Avoid Extreme Conditions: Do not expose the remote control to direct sunlight, high temperatures, humidity, or excessive dust.

Troubleshooting

Problem	Possible Cause / Solution
Remote control not working.	Batteries: Check if batteries are inserted correctly (+/-). Replace with new AAA alkaline batteries. Line of Sight: Ensure there are no obstructions between the remote and the AV receiver's IR sensor. Distance: Make sure you are within the effective operating range of the remote control.
Buttons are unresponsive or sticky.	Dirt/Debris: Clean the remote control surface with a soft, dry cloth. Battery Level: Low batteries can cause inconsistent performance. Replace them.
Remote works intermittently.	Weak Batteries: Replace batteries. Interference: Ensure no strong light sources (like direct sunlight or certain types of lighting) are interfering with the IR signal.

Specifications

Feature	Detail
Model Number	RC-157
Compatibility	Sherwood AV Receiver RX-4208, RX-4508, RX4208, RX4508
Power Source	2 x AAA Alkaline Batteries (not included)
Product Dimensions	6 x 2 x 0.5 inches (approximately 15.24 x 5.08 x 1.27 cm)
Item Weight	2.68 ounces (approximately 75.97 grams)
Color	Black
Special Feature	Ergonomic design
Manufacturer	YUDAXINFACTORY
Country of Origin	China

Warranty and Support

This product is a replacement remote control. For specific warranty information, please refer to the seller's policy or contact the seller directly. For technical support or inquiries regarding compatibility, please reach out to the manufacturer or seller.

Seller: yuedaxindian

Manufacturer: YUDAXINFACTORY

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.