Xigmatek CUBI II Black (EN45486)
Contents
XIGMATEK CUBI II Cube PC Case User Manual
Model: CUBI II Black (EN45486)
Brand: Xigmatek
1. Product Overview
The Xigmatek Cubi II is a cube PC case designed to showcase internal components through its three-panel tempered glass design, offering an unobstructed panoramic view. This EATX Mid-Tower case comes equipped with six 120mm ARGB fans and can accommodate graphics cards up to 370mm in length, providing an optimal environment for building a high-performance gaming machine.

Figure 1: Front view of the XIGMATEK CUBI II PC Case, showcasing its tempered glass panels and illuminated ARGB fans.
2. Setup Guide
2.1 Unpacking and Inspection
- Carefully remove the PC case from its packaging.
- Inspect the case for any signs of damage during transit. If damage is found, contact your retailer immediately.
- Remove all protective films from the tempered glass panels.
2.2 Component Installation
The XIGMATEK CUBI II is designed for easy installation of your PC components. Follow these general steps:

Figure 2: Side view of the XIGMATEK CUBI II PC Case, illustrating the internal layout for component installation, including motherboard tray and fan mounts.
- Motherboard Installation: Secure your EATX, ATX, Micro-ATX, or Mini-ITX motherboard to the standoffs provided. Ensure proper alignment with the I/O shield.
- Power Supply Installation: Install your power supply unit (PSU) in the designated rear mounting area.
- Storage Drive Installation: Mount your 2.5" SSDs or 3.5" HDDs in the available drive bays.
- Graphics Card Installation: Insert your graphics card into the PCIe slot. The case supports cards up to 370mm in length.
- Cable Management: Utilize the cable routing cutouts and tie-down points behind the motherboard tray for a clean build and improved airflow.
- Fan and Radiator Installation: The case comes with six pre-installed 120mm ARGB fans. Additional fans or radiators can be installed in supported locations (top, front, rear, bottom) as per your cooling requirements.
3. Operating Instructions
3.1 Powering On and Front Panel Controls
After all components are installed and cables connected, you can power on your system.

Figure 3: Top view of the XIGMATEK CUBI II PC Case, highlighting the front I/O panel with USB ports and power button.
- Power Button: Located on the top panel (refer to Figure 3). Press to power on or off your system.
- USB Ports: The case features 3 USB ports on the top panel for connecting peripherals.
- Audio Jacks: Standard headphone and microphone jacks are available for audio connectivity.
3.2 ARGB Lighting Control
The pre-installed ARGB fans can be controlled via your motherboard's ARGB software (if supported) or a dedicated ARGB controller (if included or purchased separately). Refer to your motherboard manual for software-based control instructions.
4. Maintenance
Regular maintenance helps ensure optimal performance and longevity of your PC case and components.
- Dust Cleaning: Periodically clean dust filters (if present) and internal components using compressed air. Ensure the system is powered off and unplugged before cleaning.
- Tempered Glass Cleaning: Use a soft, lint-free cloth and a non-abrasive glass cleaner to clean the tempered glass panels. Avoid harsh chemicals.
- Fan Maintenance: Check fans for dust buildup and ensure they spin freely. Clean fan blades gently if necessary.
5. Troubleshooting
This section addresses common issues you might encounter.
| Issue | Possible Cause | Solution |
|---|---|---|
| System does not power on. | Loose power cables, faulty PSU, incorrect front panel header connection. | Check all power connections (PSU, motherboard, wall outlet). Verify front panel header connections to the motherboard. Test PSU if possible. |
| Fans are not spinning or ARGB lighting is not working. | Loose fan/ARGB connections, faulty fan/controller, software issue. | Ensure all fan and ARGB cables are securely connected to the motherboard or controller. Check motherboard ARGB software settings. |
| Poor airflow or high temperatures. | Dust buildup, incorrect fan orientation, insufficient cooling. | Clean dust filters and internal components. Verify fan direction for optimal airflow (intake/exhaust). Consider adding more fans or upgrading cooling solutions if temperatures remain high. |
6. Specifications
| Feature | Detail |
|---|---|
| Brand | Xigmatek |
| Model Name | CUBI II Black |
| Item Model Number | EN45486 |
| Case Type | Tower (Cube) |
| Color | Black |
| Material | Alloy Steel |
| Special Features | 3 Tempered Glass Panels, Integrated Fan, ARGB Lighting |
| Motherboard Compatibility | Extended ATX, ATX, Micro-ATX, Mini-ITX |
| Maximum Graphics Card Length | 370 mm |
| Pre-installed Fans | 6 x 120mm ARGB Fans |
| Cooling Method | Air |
| Total USB Ports | 3 |
| Recommended Product Use | Gaming |
| Manufacturer | XIGMATEK |
| Country of Origin | China |
7. Warranty and Support
For warranty information and technical support, please refer to the official Xigmatek website or contact your point of purchase. Keep your proof of purchase for warranty claims.
For the latest drivers, software, and FAQs, visit the Xigmatek support page. Product specifications and features are subject to change without notice.
Documents and downloads
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.