Introduction
Thank you for choosing the Cofun 3-in-1 Stainless Steel Pasta Maker Attachment. This accessory is designed to seamlessly integrate with your KitchenAid Stand Mixer, simplifying the process of making fresh homemade pasta. It combines a pasta roller, spaghetti cutter, and fettuccine cutter into a single unit, offering convenience and efficiency.
Please read this manual thoroughly before first use to ensure proper setup, operation, and maintenance.
1. Setup
1.1 Unpacking and Inspection
Carefully remove all components from the packaging. Inspect the pasta maker attachment for any signs of damage. Ensure all included accessories are present: the 3-in-1 pasta maker, a cleaning brush, and this user manual.
1.2 Attaching to Your KitchenAid Stand Mixer
- Ensure your KitchenAid Stand Mixer is turned off and unplugged.
- Locate the attachment hub on the front of your stand mixer.
- Unscrew the attachment hub knob counter-clockwise and remove the hub cover.
- Insert the shaft of the pasta maker attachment into the hub, ensuring the power shaft of the attachment fits into the square hub socket.
- Rotate the attachment slightly back and forth if necessary until it slides completely into the hub.
- Tighten the attachment hub knob clockwise until the attachment is securely fastened to the mixer. Do not overtighten.


1.3 Video Guide: Attaching the Pasta Maker
2. Operating Instructions
2.1 Dough Preparation
For best results, prepare your pasta dough according to a reliable recipe. The dough should be firm but pliable, not too sticky or too dry. Ensure the dough is well-kneaded and rested before use.

2.2 Using the Pasta Roller
The pasta roller section is used to flatten your dough into sheets of desired thickness. It offers 8 thickness settings, ranging from 0.4 mm (0.016 inch) to 2 mm (0.08 inch).
- Set the thickness adjustment knob to the largest setting (typically '8' for the thickest).
- Turn your KitchenAid Stand Mixer to speed 2.
- Feed a small, flattened piece of dough into the pasta roller.
- Fold the dough sheet in half and feed it through the roller again. Repeat this process several times until the dough is smooth and pliable.
- Gradually decrease the thickness setting, feeding the dough through each setting until you reach your desired pasta sheet thickness.


2.3 Using the Spaghetti and Fettuccine Cutters
Once you have achieved the desired pasta sheet thickness, you can use the integrated cutters to create spaghetti or fettuccine.
- Ensure the mixer is still on speed 2.
- Carefully feed the pasta sheet into either the spaghetti cutter or the fettuccine cutter slot. The attachment features a removable safety flap that helps guide the dough and keeps your hands safe.
- As the pasta emerges, catch it gently and lay it on a floured surface or hang it to dry.


3. Maintenance
3.1 Cleaning Instructions
Proper cleaning ensures the longevity and optimal performance of your pasta maker attachment.
- Important: The pasta maker attachment is NOT dishwasher safe. Do not immerse it in water or any other liquids.
- After each use, allow any residual dough to dry on the attachment for approximately 15-20 minutes. This makes it easier to remove.
- Use the provided cleaning brush to gently remove any dried dough from the rollers and cutters. A wooden skewer or toothpick can be used for hard-to-reach areas.
- Wipe the exterior of the attachment with a clean, damp cloth.
- Ensure the attachment is completely dry before storing.

4. Troubleshooting
4.1 Common Issues and Solutions
- Dough sticking to rollers/cutters: Ensure your dough is not too sticky. Add a small amount of flour to the dough or dust the rollers lightly with flour. Make sure the dough is properly rested.
- Uneven pasta sheets: Ensure your dough piece is flattened evenly before feeding it into the roller. Fold and re-feed the dough through the widest setting several times to achieve a consistent texture.
- Pasta not cutting cleanly: This usually indicates the dough is too soft or too dry. Adjust your dough consistency. Ensure the attachment is clean and free of dried dough.
- Attachment not fitting securely: Double-check that the attachment hub knob is fully unscrewed and the hub cover is removed. Ensure the power shaft is correctly aligned with the square socket in the mixer hub before tightening the knob.
5. Specifications
- Brand: Cofun
- Model: C2406
- Material: 304 Stainless Steel
- Color: Silver
- Item Weight: 2.86 Pounds
- Thickness Settings: 8 (0.4 mm to 2 mm)
- Included Components: Pasta attachment, Cleaning Brush, User Manual
- Operation Mode: Automatic (via KitchenAid Stand Mixer)
- Dishwasher Safe: No
6. Warranty
Specific warranty information for the Cofun 3-in-1 Stainless Steel Pasta Maker Attachment is not provided in this manual. For details regarding warranty coverage, terms, and conditions, please refer to the product packaging or contact Cofun customer support directly.
7. Support
If you encounter any issues or have questions not covered in this manual, please contact Cofun customer support for assistance. Contact information can typically be found on the product packaging or the official Cofun website.