Introduction
The Pro-Ject T1 Evo Phono Turntable is designed to deliver high-fidelity audio for vinyl enthusiasts. This model features a built-in phono pre-amplifier, allowing for direct connection to various audio systems. It comes equipped with an Ortofon OM 10 moving magnet cartridge, pre-aligned for optimal performance. The turntable's plinth is CNC-machined, avoiding plastic components to minimize resonant hollow spaces, ensuring pure sound reproduction. An elegant dust cover with adjustable hinges and a low-capacitance Connect it Phono E RCA cable are included for convenience and quality.
Setup Guide
1. Unpacking and Placement
Carefully remove all components from the packaging. Place the turntable on a stable, level surface away from direct sunlight, heat sources, and excessive vibration. Ensure adequate ventilation around the unit.
Figure 1: Pro-Ject T1 Evo Phono Turntable with dust cover open.
Figure 2: Pro-Ject T1 Evo Phono Turntable with dust cover closed, protecting the components.
2. Assembly
- Place the platter onto the spindle.
- Carefully place the felt mat on top of the platter.
- Attach the dust cover by aligning its hinges with the slots on the turntable's base.
3. Connections
Connect the included RCA cable from the turntable's output to an available input on your amplifier or powered speakers. Since this model has a built-in phono pre-amplifier, you can connect it directly to a line-level input (e.g., AUX, CD, Line In). Ensure the ground wire is connected from the turntable to your amplifier's ground terminal to minimize hum.
Figure 3: Rear connections for RCA output and ground wire.
Connect the power adapter to the turntable and then to a wall outlet.
Operating Instructions
1. Power On/Off
Locate the power switch on the side of the turntable. Flip the switch to the 'On' position to power on the unit. The platter will begin to rotate. Flip to 'Off' to power down.
Figure 4: Power switch location.
2. Playing a Record
- Ensure the dust cover is open or removed.
- Place your vinyl record onto the felt mat on the platter.
- Carefully remove the stylus protector from the cartridge.
- Lift the tonearm using the tonearm lift lever.
- Gently move the tonearm over the desired starting groove of the record.
- Lower the tonearm using the tonearm lift lever. The stylus will gently descend onto the record, and playback will begin.
- To stop playback, lift the tonearm using the lever and return it to its rest.
Figure 5: Tonearm and Ortofon OM 10 cartridge.
Figure 6: Ortofon OM 10 cartridge detail.
3. Bluetooth Connectivity
The T1 Evo Phono Turntable supports Bluetooth connectivity for wireless audio streaming to compatible Bluetooth speakers or headphones. Refer to your Bluetooth device's manual for pairing instructions. The turntable will automatically attempt to connect to previously paired devices when powered on.
Maintenance
1. Cleaning the Turntable
- Wipe the plinth and dust cover with a soft, dry, lint-free cloth. Do not use abrasive cleaners or solvents.
- For the acrylic dust cover, use a specialized acrylic cleaner to prevent scratches.
2. Stylus Care
- Regularly inspect the stylus for dust and debris.
- Use a soft stylus brush, brushing gently from back to front, to remove any accumulated particles.
- Replace the stylus when sound quality degrades or after approximately 1,000 hours of playback.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound or very low sound | Incorrect input selection on amplifier; loose cables; volume too low. | Ensure amplifier input matches turntable connection (e.g., Line In); check all cable connections; increase volume. |
| Humming sound | Ground wire not connected; interference from other electronics. | Connect the ground wire securely; move turntable away from other electronic devices. |
| Skipping or distorted sound | Dirty or worn stylus; record is dirty or damaged; turntable not level. | Clean the stylus; clean the record; ensure turntable is on a level surface; replace stylus if worn. |
| Platter not spinning | Power not connected; power switch off. | Check power connection; ensure power switch is in the 'On' position. |
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 13.19 x 16.34 x 3.94 inches |
| Item Weight | 14.92 pounds |
| ASIN | B0DHTXH32G |
| Item Model Number | T1 Evo with Preamp |
| Manufacturer | Pro-Ject |
| Brand | Pro-Ject |
| Connectivity Technology | Wired |
| Maximum Rotational Speed | 45 RPM |
| Special Feature | Adjustable Speed |
| Style | Built-in Preamp |
| Color | Satin White |
| Model Name | T1 Evo with Preamp |
| Signal-to-Noise Ratio | 70 dB |
| Date First Available | September 24, 2024 |
Warranty and Support
Warranty Information
This Pro-Ject T1 Evo Phono Turntable comes with a standard manufacturer's warranty. Please refer to the warranty card included in your product packaging for specific terms, conditions, and duration. Retain your proof of purchase for warranty claims.
Customer Support
For technical assistance, troubleshooting beyond this manual, or service inquiries, please contact Pro-Ject customer support. Visit the official Pro-Ject website for contact details and additional resources.
Note: Always ensure to use genuine Pro-Ject replacement parts and accessories to maintain product performance and warranty validity.
