1. Introduction
This instruction manual provides essential information for the proper use and maintenance of your Hitachi EPR-26G remote control. This remote is designed for use with specific Hitachi air purifier models. Please read this manual thoroughly before operating the remote control to ensure correct functionality and to prevent damage.
2. Product Overview
The Hitachi EPR-26G remote control allows convenient operation of your compatible Hitachi air purifier from a distance. It features clearly labeled buttons for various functions.

Image 1: Front view of the Hitachi EPR-26G remote control. The remote is black with five circular buttons and the Hitachi logo at the bottom. Buttons are labeled in Japanese: 'Operation/Stop', 'Mode', 'Fan Speed', 'Timer', and 'One-Shot Turbo'.
2.1. Button Functions
- 運転/停止 (Operation/Stop): Powers the air purifier on or off.
- モード (Mode): Cycles through various operating modes (e.g., automatic, silent, pollen).
- 風量 (Fan Speed): Adjusts the fan speed (e.g., low, medium, high).
- タイマー (Timer): Sets the operating timer for automatic shutdown.
- 一発ターボ (One-Shot Turbo): Activates a temporary high-power mode for rapid air purification.
3. Compatibility
This Hitachi EPR-26G remote control (Part Number: EP-GZ30 008) is compatible with the following Hitachi air purifier models:
- EP-BKZ30
- EP-GZ30
- EP-H300
- EP-HZ30
- EP-JZ30
- EP-KZ30
- EP-LZ30
- EP-MZ30
- EP-NZ30
- EP-PZ30
- EP-Z30R
- EP-Z30S
- EP-ZN30A
- EP-ZN30S
4. Setup: Battery Installation
The remote control requires two AAA (R03/UM-4) dry cell batteries. Follow these steps to install them:
- Locate the battery compartment cover on the back of the remote control.
- Slide the battery cover downwards to open it.
- Insert two AAA (R03/UM-4) batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery cover back into place until it clicks securely.

Image 2: Back view of the Hitachi EPR-26G remote control, showing the battery compartment cover with a warning label in Japanese.

Image 3: Back view of the Hitachi EPR-26G remote control with the battery cover removed, revealing the two AAA battery slots with polarity indicators.
Important Notice:
- Always insert batteries with the correct polarity.
- Do not mix new and old batteries.
- Do not mix different types of batteries.
5. Operating Instructions
Point the remote control directly at the air purifier's receiver window. Ensure there are no obstructions between the remote and the air purifier.
- Power On/Off: Press the 運転/停止 button once to turn the air purifier on. Press it again to turn it off.
- Changing Mode: Press the モード button repeatedly to cycle through available operating modes (e.g., Auto, Silent, Pollen, Deodorize). The current mode will be displayed on the air purifier's panel.
- Adjusting Fan Speed: Press the 風量 button repeatedly to select your desired fan speed (e.g., Low, Medium, High, Auto).
- Setting Timer: Press the タイマー button to set the operating duration. Each press typically increases the timer setting by a fixed increment (e.g., 1 hour). Refer to your air purifier's main manual for specific timer options.
- One-Shot Turbo: Press the 一発ターボ button to activate a temporary high-power fan speed for quick air purification. This mode usually runs for a set period and then returns to the previous settings.
6. Maintenance
6.1. Battery Replacement
When the remote control's range decreases or it stops responding, it is time to replace the batteries. Follow the battery installation steps in Section 4. Always replace both batteries simultaneously with new ones of the same type (AAA/R03/UM-4).
6.2. Cleaning
Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners, abrasive pads, or chemical solvents, as these can damage the surface or internal components.
7. Troubleshooting
If the remote control is not functioning as expected, consider the following:
- No Response:
- Check if the batteries are inserted correctly with the proper polarity.
- Replace old batteries with new ones.
- Ensure there are no obstructions between the remote control and the air purifier.
- Confirm the remote is pointed directly at the air purifier's receiver.
- Limited Range:
- Replace the batteries.
- Ensure no strong light sources (e.g., direct sunlight, fluorescent lights) are interfering with the signal.
If problems persist, consult the main instruction manual for your Hitachi air purifier or contact customer support.
8. Specifications
| Brand | Hitachi |
| Remote Model | EPR-26G |
| Part Number | EP-GZ30 008 |
| Power Source | 2 x AAA (R03/UM-4) Dry Cell Batteries |
| Dimensions (Approx.) | 12 x 11.5 x 1.5 cm (Package Size) |
| Weight (Approx.) | 30 g (Package Weight) |
9. Warranty and Support
For information regarding warranty coverage, service, or technical support, please refer to the documentation provided with your Hitachi air purifier or visit the official Hitachi website. You may also find detailed information on the manufacturer's support page for specific parts: