Introduction
This manual provides essential information for the proper use, setup, maintenance, and care of your Oakley MOD7 Integrated Ski Helmet. Please read this manual thoroughly before using your helmet to ensure optimal performance and safety.
The Oakley MOD7 Integrated Ski Helmet is designed for snow sports, offering advanced protection and integrated goggle functionality. It features Oakley’s Secure-Connect System, an integrated retention system, MIPS technology, and Prizm Lens technology for enhanced vision and comfort.

Image: Front view of the Oakley MOD7 Integrated Ski Helmet in black with a Prizm Iridium lens.
Safety Information
General Safety Guidelines
- Always wear your helmet when participating in snow sports.
- Ensure the helmet fits snugly and is properly secured before each use.
- Never modify your helmet. Any alterations can compromise its protective capabilities.
- Inspect your helmet regularly for any signs of damage. If damaged, replace it immediately.
- The helmet is designed to absorb impact by partial destruction of the shell and liner. Even if no visible damage is present, a helmet that has sustained an impact should be replaced.
MIPS Technology
The MOD7 helmet integrates MIPS (Multi-directional Impact Protection System) technology. MIPS is a low-friction layer designed to reduce rotational forces that can result from certain impacts. This system enhances impact protection by allowing a relative motion between the head and the helmet, adding an extra layer of safety.

Image: Oakley MOD7 helmet showcasing the BOA fit system dial and MIPS technology logo.
Setup
1. Helmet Fit Adjustment
Achieving a secure and comfortable fit is crucial for helmet performance.
- Sizing: Refer to the size chart below to determine the correct helmet size based on your head circumference.

Image: Head circumference measurement guide for Oakley MOD7 helmet sizes (S: 20-22 inches, M: 22-23 inches, L: 23-24 inches).
- BOA® Fit System: The helmet is equipped with a BOA® wheel at the back. Turn the dial clockwise to tighten the fit for a snug feel, and counter-clockwise to loosen. Adjust until the helmet is firm but comfortable, without excessive pressure points.
- Chin Strap: Fasten the chin strap securely under your chin. Adjust the strap length so that it is snug but does not cause discomfort or restrict breathing. The strap should be tight enough that the helmet cannot be easily pulled off your head.
2. Goggle Integration (Secure-Connect System)
The MOD7 features an integrated goggle system for a seamless experience.
- Attaching Goggles: The goggle frame clicks into the front of the helmet using mechanical and magnetic connections. Align the goggle frame with the helmet's front opening and gently push until it clicks into place.
- Adjusting Goggle Fit: Use the spring-loaded adjusters located over the ears to control how tightly the lens is held to your face. This allows for a customized and secure goggle fit.
- Removing Goggles: Spring-loaded releases are built into the edges of the lens. Press these releases to detach the goggle frame from the helmet. The goggles can then be clipped to the top of the helmet for storage when not in use.

Image: Multiple views of the Oakley MOD7 helmet, illustrating its integrated design and features.
Operating Instructions
Ventilation Control
The helmet features strategic ventilation to manage airflow and prevent fogging.
- Main Ventilation: Airflow is primarily managed through a channel on the top of the helmet. This system helps regulate temperature and reduce goggle fogging.
Lens Care and Handling
The Prizm Lens technology provides enhanced vision. Handle lenses with care.
- Avoid touching the inner surface of the lens to prevent scratching or damaging anti-fog coatings.
- Use the provided Oakley Microfiber Bag or a soft, clean cloth for cleaning.
Maintenance
Cleaning Your Helmet
- Exterior: Clean the helmet's exterior with a soft cloth, mild soap, and water. Avoid harsh chemicals or abrasive cleaners.
- Interior Liner: The interior liner can typically be removed for washing. Follow the instructions on the care label. Use mild soap and cold water, then air dry. Ensure it is completely dry before reinserting.
- Goggles/Lens: Use the provided cleaning solution and cloth for the goggle lens. Do not use paper towels or rough materials, as they can scratch the lens.
Storage
- Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures.
- Use the included Oakley helmet bag for protection during storage and transport.
- Avoid placing heavy objects on the helmet, as this can deform the shell.
Inspection
- Regularly inspect the helmet for cracks, dents, or any signs of wear and tear on the shell, liner, straps, and buckles.
- Check the goggle integration points for any damage or loose connections.
- If any damage is found, discontinue use and replace the helmet.
Troubleshooting
Common Issues and Solutions
- Helmet feels loose: Adjust the BOA® Fit System dial clockwise until a snug, comfortable fit is achieved. Ensure the chin strap is also tightened.
- Goggles fogging: Ensure the helmet's ventilation system is clear. Check that the goggles are properly seated against your face to prevent air gaps. Clean the lens with the provided cloth.
- Goggles not attaching securely: Verify that the goggle frame is correctly aligned with the helmet's connection points and that the mechanical and magnetic connections engage fully.
- No speaker pockets: Please note that the Oakley MOD7 helmet does not feature integrated speaker pockets in the ear pads. This design choice prioritizes a streamlined profile and specific fit characteristics.
If you encounter issues not covered here, please contact Oakley customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | Oakley |
| Model Name | MOD7 |
| Model Number | OHFOS900642 |
| UPC | 840270363715 |
| Age Range | Adult |
| Outer Material | Polycarbonate (PC) |
| Inner Material | Expanded Polystyrene |
| Special Features | MIPS Technology, Secure-Connect System, BOA® Fit System, Prizm Lens Technology |
| Recommended Use | Skiing, Snowboarding |
| Item Weight | 1.5 Pounds |
| Included Components | Oakley Microfiber Bag, Oakley Sticker, Designer iWear Collapsible Water Bottle with Carabiner |

Image: The included Designer iWear Collapsible Water Bottle with Carabiner.
Warranty
Oakley stands by the quality and durability of its products. The MOD7 Integrated Ski Helmet is backed by Oakley's commitment to quality, ensuring exceptional durability and trusted protection. For specific warranty terms and conditions, please refer to the official Oakley website or contact customer support.
Support
For further assistance, product inquiries, or warranty claims, please visit the official Oakley support website or contact their customer service department.
Official Oakley Website: www.oakley.com
Customer Service: Refer to the Oakley website for regional contact information.