Introduction
Thank you for choosing the MARK ADLER Xeno 7.6 Electric Dual Motor Desk Frame. This manual provides detailed instructions for the assembly, operation, maintenance, and troubleshooting of your new height-adjustable desk frame. Please read this manual carefully before installation and use to ensure proper function and safety.
Safety Information
To prevent injury or damage to the product, please observe the following safety guidelines:
- Do not exceed the maximum load capacity of 80 kg (176 lbs).
- Ensure all cables are properly routed and secured to avoid entanglement during height adjustments.
- Keep children and pets away from the desk during operation.
- Use the anti-collision system with caution to prevent damage or injury.
- Do not place hands or other body parts near moving parts of the frame.
- Only use the desk frame indoors in a dry environment.
- If any unusual sounds or movements occur, immediately stop operation and consult the troubleshooting section or contact support.
Setup and Assembly
The MARK ADLER Xeno 7.6 desk frame requires assembly. It is recommended that two people assemble the desk frame for ease and safety.
Package Contents
Before starting assembly, verify that all components are present. The package includes the electric dual motor desk frame, control panel, and necessary mounting hardware. A desktop is not included and must be purchased separately.
Assembly Steps
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
- Assemble Legs and Crossbars: Attach the lifting columns to the feet and then connect the crossbars. Ensure all screws are tightened securely.
- Install Motors and Control Box: Mount the dual motors and the control box according to the diagrams. Connect all motor and power cables to the control box.
- Attach Control Panel: Secure the control panel to the desired location on the desk frame, typically on the front edge.
- Mount Desktop: Place your chosen desktop (120-150 cm width recommended) onto the assembled frame. Secure the desktop to the frame using appropriate screws. The frame supports both left and right-hand L-shaped configurations.
- Cable Management: Route all cables neatly using cable ties or clips to prevent them from interfering with the desk's movement.
- Attach Accessories: Install the included headphone hook and bag holder as desired.
Image: MARK ADLER Xeno 7.6 Desk Frame layout showing dimensions and components. The frame is adjustable from 72 cm to 118 cm in height, and accommodates desktops from 105 cm to 150 cm in width on the main section, and 108 cm on the return section, with a depth of 58 cm.
Image: Diagram illustrating the robust and stable construction of the MARK ADLER Xeno 7.6 desk frame, highlighting its dual column design and adjustable width for different desktop sizes.
Operating Instructions
The MARK ADLER Xeno 7.6 desk frame features an intuitive control panel for easy height adjustment and memory functions.
Control Panel Functions
Image: Close-up of the MARK ADLER Xeno 7.6 control panel, showing the up/down arrows, memory buttons (1, 2, 3), and integrated USB and USB-C charging ports.
- Height Adjustment: Use the ▲ (Up) and ▼ (Down) arrow buttons to manually adjust the desk height. The height range is from 72 cm to 118 cm.
- Memory Presets: The control panel has three programmable memory positions (1, 2, 3).
- To save a height: Adjust the desk to your desired height. Press the "S" button, then press one of the number buttons (1, 2, or 3) within 3 seconds. The display will show "S-" followed by the number to confirm.
- To recall a saved height: Simply press the corresponding number button (1, 2, or 3). The desk will automatically move to the saved position.
- USB Charging Ports: The integrated USB and USB-C ports allow you to conveniently charge your devices directly from the desk.
Image: Graphic illustrating the height adjustment range of the MARK ADLER Xeno 7.6 desk frame, from 72 cm to 118 cm, emphasizing the smooth transition between sitting and standing positions.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your MARK ADLER Xeno 7.6 desk frame.
- Cleaning: Wipe the desk frame with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish.
- Cable Check: Periodically inspect all cables for wear or damage. Ensure they are securely connected and not pinched.
- Screw Tightness: Occasionally check and tighten any loose screws, especially after initial assembly and a few weeks of use.
- Lubrication: The lifting columns are generally maintenance-free. Do not apply lubricants unless specifically instructed by the manufacturer.
Troubleshooting
If you encounter issues with your desk frame, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Desk does not move. | Power cable disconnected, control box error, overload. | Check power connection. Unplug and replug the power cord. Reduce load if exceeding 80 kg. Perform a reset (see below). |
| Uneven movement or noise. | Loose connections, uneven load, obstruction. | Check all screws and connections. Ensure weight is evenly distributed. Remove any obstructions. |
| Memory function not working. | Memory not properly set, power interruption. | Re-program the memory positions. Perform a reset. |
| Error code displayed. | Specific system error. | Refer to the specific error code in the full manual (if available) or contact customer support. Often, a reset can resolve temporary errors. |
Reset Procedure
If the desk is not functioning correctly, a reset may resolve the issue.
- Unplug the power cord from the wall outlet.
- Wait for at least 30 seconds.
- Plug the power cord back into the wall outlet.
- Press and hold the ▼ (Down) button until the desk reaches its lowest position and slightly retracts, then stops. This indicates a successful reset.
Specifications
| Feature | Detail |
|---|---|
| Brand | MARK ADLER |
| Model Number | Xeno 7.6 |
| Desk Design | Computer Desk (L-shaped frame) |
| Color | Black |
| Material | Metal (Frame) |
| Height Adjustment Range | 72 cm - 118 cm (28.3 inches - 46.5 inches) |
| Recommended Desktop Width | 120 cm - 150 cm (main section) |
| Depth | 58 cm (22.8 inches) |
| Maximum Load Capacity | 80 kg (176 lbs) |
| Motors | Dual Motor System |
| Memory Positions | 3 programmable positions |
| Special Features | Electric height adjustment, Ergonomic, Memory function, USB & USB-C ports, Headphone hook, Bag holder |
| Assembly Required | Yes (2 people recommended) |
| Country of Origin | China |
Warranty
The MARK ADLER Xeno 7.6 Electric Dual Motor Desk Frame comes with a Limited Warranty. Please refer to the warranty card included with your product or contact MARK ADLER customer support for specific terms and conditions. This warranty typically covers manufacturing defects and malfunctions under normal use.
Support
For further assistance, technical support, or warranty claims, please contact MARK ADLER customer service.
- Online Support: Visit the official MARK ADLER website for FAQs, additional resources, and contact forms.
- Email: Refer to your product packaging or the official website for the customer support email address.
- Phone: Refer to your product packaging or the official website for customer support phone numbers.
When contacting support, please have your product model number (Xeno 7.6) and purchase information readily available.
