1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your eRapta ACT1002 Magnetic Wireless Backup Camera System. Please read this manual thoroughly before using the product to ensure proper function and safety.
2. Package Contents
Verify that all items listed below are included in your package:
- 10.1" Monitor (x1)
- Magnetic Camera (x2)
- Antenna (x5)
- Car Charger (x1)
- U-shaped Bracket (x1)
- Type-C Cable (x1)
- Camera Screws
- Fan-shaped Bracket (x1)
3. Setup and Installation
3.1 Camera Installation
The eRapta ACT1002 cameras feature a strong magnetic base for easy, no-wiring installation on any metal surface. Ensure the camera is fully charged before initial use.
- Charge Cameras: Use the included Type-C cable to fully charge both magnetic cameras. The built-in 9600mAh battery provides extended use.
- Attach Antennas: Screw the antennas onto the designated ports on each camera.
- Mount Cameras: Securely attach the cameras to any metal surface on your vehicle (RV, trailer, truck, tractor). The magnetic base ensures a firm hold. For non-magnetic surfaces, use the provided fan-shaped bracket and screws for permanent installation.
3.2 Monitor Installation
- Attach Bracket: Secure the 10.1-inch monitor to your dashboard or windshield using the U-shaped or fan-shaped bracket.
- Power Monitor: Plug the monitor's car charger into your vehicle's cigarette lighter socket. The monitor will power on automatically when the vehicle starts.
4. Operating Instructions
4.1 Power On/Off
The monitor automatically turns on when the vehicle starts and powers off when the vehicle is turned off. Cameras enter sleep mode when the monitor is off to conserve battery.
4.2 Camera Pairing
The cameras and monitor are pre-paired at the factory. If re-pairing is needed, refer to the system settings menu on the monitor.
4.3 Viewing Modes
The 10.1-inch monitor supports up to four cameras and offers multiple viewing options:
- Full Screen: Displays a single camera view.
- Split Screen: Displays two camera views simultaneously.
- Quad View: Displays four camera views simultaneously (if four cameras are connected).
Use the 'CH' button on the monitor to cycle through available camera channels and viewing modes.
4.4 Parking Assistance
The 10.1-inch monitor features adjustable parking lines with a 150° wide-angle view. Customize parking line settings (width, height, position) using the buttons above the screen for precise guidance.
4.5 Loop Video Recording
Insert an SD card (not included, max 128GB) into the monitor to activate loop recording. This feature continuously records footage, overwriting the oldest files when the card is full. Recorded videos can be played back directly on the monitor.
5. Features Overview
- HD1080P Resolution: Upgraded resolution for vibrant image quality day and night.
- IR Night Vision: Ensures clear visibility in low-light conditions.
- 9600mAh Rechargeable Battery: Extended battery life with automatic sleep mode for power saving. Charges via Type-C.
- IP69K Waterproof: Durable construction to withstand harsh weather and temperatures from -6°F to 151°F.
- Dual-Antenna 2.4GHz Wireless Signal: Provides strong and stable signal transmission without delay.
6. Maintenance
- Cleaning: Use a soft, damp cloth to clean the camera lenses and monitor screen. Avoid abrasive cleaners.
- Battery Care: For optimal battery life, fully charge the cameras before long periods of inactivity.
- Firmware Updates: Check the eRapta official website periodically for any available firmware updates to ensure optimal performance.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No Signal on Monitor | Camera not powered on or out of range; interference. | Ensure cameras are charged and powered. Move cameras closer to the monitor. Check for strong signal interference. |
| Poor Image Quality | Dirty lens; low light (without IR); signal interference. | Clean camera lens. Ensure IR night vision is active in low light. Reduce signal interference. |
| Monitor Not Powering On | Car charger not properly connected or vehicle's power outlet is off. | Check car charger connection and vehicle's power. Ensure vehicle ignition is on. |
8. Specifications
- Model Number: ACT1002
- Screen Size: 10.1 Inches
- Display Technology: LCD
- Optical Sensor Technology: CMOS
- Real Angle of View: 150 Degrees
- Battery: 9600 mAh Lithium Ion (rechargeable)
- Waterproof Rating: IP69K
- Operating Temperature: -6°F to 151°F
- Wireless Frequency: 2.4GHz
- Max SD Card Support: 128GB (not included)
9. Warranty and Support
eRapta offers a 2-year warranty for the ACT1002 Magnetic Wireless Backup Camera System. For any questions, concerns, or technical assistance, please contact our dedicated 24-hour online customer service.
Your satisfaction is our priority. Please refer to the product packaging or the official eRapta website for contact details.
10. Official Product Videos
10" 2 Magnetic Wireless Backup Camera Kit
This video demonstrates the features and functionality of the eRapta 10-inch magnetic wireless backup camera kit, highlighting its ease of use and clear display.
