1. Introduction
Thank you for choosing Sunco 90W LED Barn Lights. This manual provides essential information for the safe installation, operation, and maintenance of your new outdoor lighting fixtures. Please read these instructions thoroughly before installation and retain them for future reference.
2. Safety Information
- WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installation or servicing.
- This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- Ensure all electrical connections are made correctly and securely.
- Do not handle live wires. Always wear appropriate personal protective equipment (PPE).
- Suitable for wet locations. Ensure all seals and gaskets are properly seated to maintain waterproof rating.
- Do not modify the fixture. Any modifications may void the warranty and create safety hazards.
3. Product Overview
Key Features:
- Dusk-to-Dawn Operation: Integrated photocell automatically turns the light on at dusk and off at dawn, saving energy.
- High Brightness: 90W LED delivers 12,600 lumens for powerful illumination.
- Color Temperature: 5000K Daylight for clear, bright outdoor lighting.
- Dimmable: 0-10V dimming capability for adjustable light output.
- Durable Construction: Waterproof (IP65) aluminum and polycarbonate materials for outdoor use.
- Wide Coverage: Designed to provide broad light distribution for large areas.
Components:
The Sunco Barn Light consists of a robust housing, high-efficiency LED chips, an integrated dusk-to-dawn photocell, heat dissipating fins, and an impact-resistant polycarbonate lens.
4. Setup & Installation
These fixtures are designed for easy installation on walls, poles, or posts using lag screws. Professional installation is recommended.
Installation Steps:
- Prepare the Mounting Surface: Ensure the mounting surface (wall, pole, or post) is structurally sound and can support the weight of the fixture.
- Mount the Bracket: Secure the mounting bracket to the desired location using appropriate lag screws or bolts.
- Wire the Fixture: Connect the electrical wiring (live, neutral, ground) from your power source to the fixture's wiring. If using 0-10V dimming, connect the dimming wires as per local electrical codes. Ensure power is OFF during wiring.
- Attach the Fixture: Securely attach the light fixture to the mounted bracket.
- Test Operation: Restore power and test the light's functionality, including dusk-to-dawn and dimming features if applicable.
5. Operating Instructions
Dusk-to-Dawn Functionality:
The integrated photocell sensor automatically detects ambient light levels. The fixture will illuminate when natural light falls below a certain threshold (dusk) and turn off when sufficient natural light is detected (dawn). No manual intervention is required for this feature.
0-10V Dimming:
If connected to a compatible 0-10V dimmer switch, the light output can be adjusted. Follow the dimmer manufacturer's instructions for wiring and operation. The 0-10V dimming wires are typically purple (+) and gray (-).
6. Maintenance
- Cleaning: Periodically clean the lens and housing with a soft, damp cloth to remove dirt and debris. Do not use abrasive cleaners or solvents. Ensure the fixture is off and cool before cleaning.
- Inspection: Regularly inspect the fixture for any signs of damage, loose connections, or wear. Address any issues promptly.
- Photocell: Keep the photocell sensor clear of obstructions (e.g., leaves, dirt) to ensure proper dusk-to-dawn operation.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | No power to fixture Faulty wiring Photocell obstructed or faulty | Check circuit breaker and power supply Verify wiring connections Clear photocell; test in dark conditions |
| Light stays on during the day | Photocell obstructed Light source too close to photocell | Clear photocell of obstructions Relocate fixture or shield photocell from other light sources |
| Light flickers or dims unexpectedly | Loose wiring connection Incompatible dimmer (if applicable) Power fluctuations | Check and secure all wiring connections Ensure dimmer is 0-10V compatible Consult an electrician for power supply issues |
8. Specifications
| Attribute | Value |
|---|---|
| Brand | Sunco Lighting |
| Model Number | B0DGRLGWZD |
| Wattage | 90 Watts |
| Brightness | 12600 Lumens |
| Efficiency | 140 lumens per watt |
| Color Temperature | 5000K Daylight |
| Dimmable | Yes (0-10V) |
| Voltage | 277 Volts |
| Material | Aluminum, Polycarbonate |
| Water Resistance Level | Waterproof (IP65) |
| Mounting Type | Wall Mount, Surface Mount |
| Light Source | LED |
| Item Dimensions L x W x H | 23.07"L x 15.74"W x 18.7"H |
| Item Weight | 26.87 Pounds |
9. Warranty & Support
Warranty Information:
Sunco Lighting provides a 7-year manufacturer's warranty for this product. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
Customer Support:
For technical assistance, troubleshooting, or warranty inquiries, please contact Sunco Lighting customer support. Contact details can be found on the official Sunco Lighting website or product packaging.
