1. Introduction
This manual provides essential instructions for the safe and effective installation, operation, and maintenance of the Satco 80-1497 Shallow Base Slide-On Quick Wire Socket. This product is designed for use in wet and damp locations and is optimized for rapid start lighting systems on 20-gauge panels. Please read this manual thoroughly before installation or use.
2. Safety Information
WARNING: Risk of electric shock. Installation should be performed by a qualified electrician or trained personnel only. Disconnect power at the circuit breaker before installation or servicing.
- Ensure all local and national electrical codes are followed.
- Do not exceed the maximum rated voltage (600 Volts) or wattage (660 Watts) for this product.
- Inspect the product for any damage before installation. Do not install damaged components.
- Wear appropriate personal protective equipment (PPE) during installation.
3. Product Overview
The Satco 80-1497 socket is a durable, cULus listed component designed for reliable performance in challenging environments. Its shallow base and slide-on quick wire design facilitate easy installation.
Figure 1: Satco 80-1497 Sockets (50-pack) and packaging.
Key Features:
- High Wattage Support: Capable of handling up to 660 watts.
- Wet and Damp Locations: Engineered for reliable performance in moist environments.
- Slide-On Quick Wire Design: Facilitates easy and rapid installation.
- Compact and Durable: Measures 1.25 x 1.25 x 1.75 inches with a 1.25-inch extension.
- cULus Listed: Meets recognized safety and quality standards.
- Rapid Start Application: Optimized for rapid start lighting systems.
4. Setup and Installation
The Satco 80-1497 socket is designed for straightforward installation on 20-gauge panels, commonly found in fluorescent fixtures such as troffers and wrap fixtures.
- Power Disconnection: Before beginning, ensure that power to the fixture is completely disconnected at the circuit breaker. Verify with a voltage tester.
- Access Fixture: Open or remove the cover of the lighting fixture to access the wiring and mounting points.
- Mounting: The shallow base and slide-on design allow the socket to be easily slid onto the edge of a 20-gauge panel. Ensure it is securely seated.
- Wiring: Utilize the quick wire terminals to connect the appropriate electrical wires. Ensure a secure and proper connection according to the fixture's wiring diagram. This socket is designed for rapid start applications.
- Secure and Test: Once wired, ensure all connections are firm and no bare wires are exposed. Close the fixture cover. Restore power and test the lighting system.
Figure 2: Example of socket installation in a lighting fixture.
Figure 3: The socket is suitable for use in troffer lighting fixtures.
Figure 4: The socket is also suitable for use in wrap-around fixtures.
5. Operating Instructions
Once properly installed and wired, the Satco 80-1497 socket functions as a standard lamp holder for rapid start fluorescent lamps. Operation is controlled by the fixture's power switch.
- Ensure compatible rapid start lamps are used with this socket.
- Turn on the power switch for the fixture to illuminate the lamps.
- Turn off the power switch to extinguish the lamps.
6. Maintenance
The Satco 80-1497 socket is constructed for long-lasting performance with minimal maintenance. Regular inspection is recommended.
- Cleaning: Disconnect power before cleaning. Use a dry, lint-free cloth to gently wipe the exterior of the socket if dust or debris accumulates. Do not use liquid cleaners.
- Inspection: Periodically inspect the sockets for any signs of wear, discoloration, or damage. Check wire connections for tightness. If any damage is observed, disconnect power and replace the affected socket immediately.
- Lamp Replacement: Always disconnect power before replacing lamps. Ensure replacement lamps are of the correct type and wattage.
7. Troubleshooting
If the lighting fixture is not operating correctly, consider the following common issues:
- No Light:
- Check if the circuit breaker is tripped.
- Ensure the lamp is correctly seated in the socket.
- Verify the lamp is not faulty by testing with a known working lamp.
- Inspect wiring connections for looseness or corrosion (with power disconnected).
- Flickering Light:
- Ensure the lamp is fully inserted and making good contact.
- Check for loose wiring connections.
- The lamp itself may be nearing end-of-life or faulty.
If issues persist after troubleshooting, consult a qualified electrician.
8. Specifications
| Specification | Value |
|---|---|
| Product Dimensions | 1.25 x 1.25 x 1.75 inches |
| Manufacturer | Satco |
| Material | Copper |
| Voltage Rating | 600 Volts |
| Wattage Rating | 660 Watts |
| Certification | cULus Listed |
| Application | Rapid Start, Wet and Damp Locations |
Figure 5: The socket is rated for 600 Volts.
Figure 6: The socket supports up to 660 Watts.
9. What's in the Box
Each package contains:
- Satco 80-1497 Shallow Base Slide-On Quick Wire Socket(s)
10. Warranty and Support
For warranty information or technical support, please contact Satco customer service directly. Refer to the product packaging or Satco's official website for contact details.
