1. Introduction
This manual provides essential information for the setup, operation, and maintenance of your Sovol SV06 ACE 3D Printer. Please read this guide thoroughly before operating the device to ensure proper functionality and safety.
Image 1.1: The Sovol SV06 ACE 3D Printer.
2. Setup
2.1 Unboxing and Assembly
The Sovol SV06 ACE is designed for quick assembly, typically within 15 minutes. Follow the included quick start guide for detailed steps. Ensure all components are securely fastened before proceeding.
Image 2.1: Assembly process of the Sovol SV06 ACE.
2.2 Initial Calibration and Auto-Leveling
The SV06 ACE features a fully automatic leveling system. Perform a one-click self-check to ensure correct assembly and proper component function. This process includes:
- Z-axis Tilt Calibration
- Bed Calibration
- Vibration Compensation
- PID Calibration
This automated process eliminates the need for manual bed leveling adjustments.
Image 2.2: Auto-leveling interface on the printer's touch screen.
2.3 Enhanced Structure
The SV06 ACE incorporates an upgraded frame for improved stability and performance. Key structural enhancements include:
- Upgraded X and Y axis assembly with dual-axis profiles and metal bearings/tracks for reduced noise and enhanced strength.
- Z-axis guide rods increased from 8mm to 10mm for enhanced structural stability.
Image 2.3: Structural enhancements for stability.
2.4 Software and Connectivity
The printer is compatible with OrcaSlicer (Windows/Mac), Cura-Ultimaker (Windows/Mac), and Cura-Sovol (Windows). It supports 2.4G WiFi connectivity for remote control and monitoring.
3. Operating Instructions
3.1 Printing Speed and Performance
The SV06 ACE offers a maximum printing speed of 600mm/s and an acceleration of up to 20,000mm/s². This allows for significantly faster print times compared to previous models.
Image 3.1: High-speed printing capabilities.
3.2 Filament Compatibility and Extruder
Equipped with a 300℃ high-temperature nozzle, the SV06 ACE supports a wide range of filament materials, including PETG, TPU, PLA, and ABS. The advanced planetary dual gear extruder features a 1:7.5 gear ratio, ensuring consistent and powerful filament output.
3.3 Real-time Monitoring
Monitor your print progress remotely using the Obico App. This feature allows you to check the status of your printer and control it from any location with internet access.
Image 3.2: Remote monitoring via Obico App.
3.4 User Interface and Updates
The printer features a 4.3-inch capacitive touch screen for easy operation. Firmware updates are simplified with Over-The-Air (OTA) upgrades, allowing for one-click installation of the latest features and improvements without technical skills.
Image 3.3: User interface and OTA update feature.
4. Maintenance
4.1 General Cleaning
Regularly clean the build plate with isopropyl alcohol to ensure optimal adhesion. Keep the printer's exterior free of dust and filament debris. Use a soft brush or compressed air to clean fans and hard-to-reach areas.
4.2 Extruder and Nozzle Care
Periodically check the extruder gears for filament residue and clean as necessary. If print quality degrades, consider replacing the nozzle. Refer to the manufacturer's guidelines for specific nozzle replacement procedures.
4.3 Axis Lubrication
The linear rods and bearings on the X, Y, and Z axes may require occasional lubrication to maintain smooth movement and reduce wear. Use a small amount of appropriate lubricant as recommended by Sovol.
5. Troubleshooting
5.1 Common Printing Issues
- Poor Bed Adhesion: Ensure the build plate is clean and free of grease. Re-run the auto-leveling calibration. Adjust the Z-offset if necessary.
- Stringing/Oozing: This can often be resolved by adjusting retraction settings in your slicer software. Ensure filament is dry.
- Under/Over Extrusion: Check for clogged nozzles or issues with the extruder gears. Calibrate E-steps if needed.
- Layer Shifting: Verify that belts are properly tensioned and pulleys are secure. Check for obstructions on the axis rails.
5.2 Klipper Firmware and Open Source
The SV06 ACE utilizes Klipper firmware on a 64-bit chip, offering powerful computing performance and flexibility. Its open-source nature allows for community support and customization. For advanced troubleshooting or modifications, consult the official Sovol community forums or Klipper documentation.
Image 5.1: Klipper firmware for powerful performance.
Image 5.2: Open-source platform for customization.
6. Specifications
| Feature | Specification |
|---|---|
| Model Number | SV06 ACE |
| Brand | Sovol |
| Product Dimensions | 17.32 x 15.75 x 18.11 inches (43.99 x 40.00 x 46.00 cm) |
| Item Weight | 19.8 pounds (9 Kilograms) |
| Material | Metal |
| Manufacturer | Sovol |
| Compatible Devices | OrcaSlicer (Win/Mac), Cura-Ultimaker (Win/Mac), Cura-Sovol (Win) |
| Max Print Speed | 600mm/s |
| Max Acceleration | 20,000mm/s² |
| Nozzle Temperature | Up to 300℃ |
| Extruder Type | Planetary Dual Gear Direct Drive (1:7.5 gear ratio) |
| Leveling | Fully Auto Leveling |
| Firmware | Klipper (64-bit chip, Linux-based) |
| Connectivity | 2.4G WiFi |
7. Warranty and Support
7.1 Warranty Information
For detailed warranty terms and conditions, please refer to the official Sovol website or contact Sovol customer service directly. Warranty coverage typically includes manufacturing defects for a specified period from the date of purchase.
7.2 Customer Support
If you encounter any issues or have questions regarding your Sovol SV06 ACE 3D Printer, please utilize the following resources:
- Official Sovol Website: Access FAQs, troubleshooting guides, and contact information.
- Online Community Forums: Engage with other users and experts for shared knowledge and solutions.
- OTA Updates: Ensure your printer's firmware is up-to-date for optimal performance and new features.
