Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Kingston Brass KX1071BD Vintage Hand Shower Kit. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product. Retain this manual for future reference.
The Kingston Brass KX1071BD is a single-function hand shower kit designed for a comfortable showering experience. It features durable brass construction, a 59-inch hose, a shower arm diverter for easy installation, and an adjustable wall bracket.
Package Contents
Verify that all components are present before beginning installation.
- Hand Shower Head
- 59-inch Shower Hose
- Shower Arm Diverter
- Adjustable Wall Bracket
- Installation Hardware (washers, seals, etc.)
Image 1: Overview of the Kingston Brass KX1071BD Vintage Hand Shower Kit, showing the hand shower head, hose, and diverter valve.
Setup and Installation
Before you begin, ensure the main water supply to your shower is turned off. Gather necessary tools: adjustable wrench, plumber's tape, and a soft cloth.
Step 1: Prepare the Shower Arm
- Remove your existing showerhead from the shower arm. Clean any old plumber's tape or debris from the shower arm threads.
- Apply new plumber's tape clockwise around the threads of the shower arm.
Step 2: Install the Shower Arm Diverter
- Thread the shower arm diverter onto the shower arm. Hand-tighten first, then use an adjustable wrench to tighten an additional 1/4 to 1/2 turn. Do not overtighten.
- Ensure the diverter lever is positioned for easy access.
Step 3: Connect the Shower Hose
- Connect one end of the 59-inch shower hose to the outlet on the bottom of the shower arm diverter. Ensure a washer is inside the hose connection. Hand-tighten.
- Connect the other end of the shower hose to the hand shower head. Ensure a washer is inside this connection as well. Hand-tighten.
Step 4: Install the Adjustable Wall Bracket
- Determine the desired height and location for the adjustable wall bracket.
- Mark the mounting holes. Drill pilot holes if necessary (check wall material).
- Secure the wall bracket to the wall using the provided screws and anchors.
- Place the hand shower head into the wall bracket.
Image 2: Technical drawing illustrating the dimensions and connection points of the hand shower kit components, including the diverter, hose, and hand shower head.
Step 5: Test for Leaks
- Turn on the main water supply.
- Check all connections for leaks. If leaks occur, tighten the connections slightly. Do not overtighten.
Operating Instructions
The Kingston Brass KX1071BD hand shower kit is designed for simple operation.
- Diverter Function: The shower arm diverter allows you to switch water flow between your main showerhead (if applicable) and the hand shower. Move the diverter lever to direct water to your desired outlet.
- Hand Shower Use: Remove the hand shower from its wall bracket. The single-function spray pattern provides a consistent, full spray.
- Adjustable Wall Bracket: The wall bracket allows you to adjust the angle of the hand shower for hands-free use, effectively converting it into a secondary showerhead.
Maintenance
Regular cleaning and maintenance will ensure the longevity and optimal performance of your hand shower kit.
- Cleaning the Finish: Clean the polished chrome finish with a soft, damp cloth. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the finish.
- Cleaning Nozzles: If mineral deposits build up on the hand shower nozzles, gently rub them with your finger or a soft brush to dislodge the deposits. For stubborn buildup, a solution of equal parts white vinegar and water can be applied to the nozzles for a short period, then rinsed thoroughly.
- Hose Care: Periodically check the shower hose for kinks or damage. Ensure it hangs freely when not in use to prevent stress on the connections.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaks from connections. | Loose connections, missing or damaged washers, insufficient plumber's tape. | Ensure connections are hand-tightened, then use a wrench for a final 1/4 to 1/2 turn. Check for and replace any damaged washers. Reapply plumber's tape if necessary. |
| Low water pressure from hand shower. | Mineral buildup in nozzles, partially closed diverter, low household water pressure. | Clean hand shower nozzles (see Maintenance). Ensure diverter is fully engaged for the hand shower. Check household water pressure. |
| Diverter not switching properly. | Debris in diverter mechanism, diverter not fully engaged. | Ensure the diverter lever is moved completely to the desired position. If issues persist, contact customer support. |
Specifications
- Model: KX1071BD
- Brand: Kingston Brass
- Finish: Polished Chrome
- Material: Brass
- Style: Vintage
- Mounting Type: Wall Mount (for bracket)
- Hand Shower Head Size: 7-1/2'' (L) x 2-1/16'' (W) x 3-3/4'' (H)
- Hose Length: 59 inches
- Flow Rate: 1.8 GPM / 6.8 LPM at 80 PSI
- Hose Connection: 1/2-14 NPSM
- Item Weight: Approximately 2.39 pounds
- Special Features: Corrosion Resistant
Warranty and Support
For warranty information or technical support, please contact Kingston Brass customer service. Refer to your product packaging or the official Kingston Brass website for the most current contact details and warranty terms.
Kingston Brass Official Website: www.kingstonbrass.com
