Y-METDRIVING Wireless Steering Wheel Remote Control (Model TH0018-B) Instruction Manual

1. Product Overview

The Y-METDRIVING Wireless Steering Wheel Remote Control (Model TH0018-B) provides convenient access to car stereo functions directly from your steering wheel. It is designed for compatibility with most Android car stereos and Y-METDRIVING portable car stereos.

Image 1.1: Package contents including dual-sided controllers, Android adapter cable, and disassembly tool.

Key Features:

• Enhanced Control: Features 9 frequently used buttons and 1 customizable button for comprehensive control.
• Broad Compatibility: Works with most Android car stereos that support steering wheel button learning. Direct use with Y-METDRIVING portable car stereos.
• Signal Indicator: A signal indicator light illuminates briefly when a button is pressed, confirming operation, especially useful at night.
• Long Battery Life: Designed to operate for approximately 3 to 6 months on a single charge under normal usage conditions.

Image 1.2: Detailed view of the remote control buttons and their functions, including volume, track, call, and customizable options.

Product Dimensions:

Image 1.3: The remote control measures approximately 12.5cm in length, 3.5cm in width, and 2.5cm in thickness.

2. Setup and Installation

Follow these steps to install and configure your Y-METDRIVING Wireless Steering Wheel Remote Control.

2.1 Wiring the Receiver

The receiver connects to your car stereo's wiring harness. Ensure the vehicle's ACC power is off before proceeding.

Image 2.1: Wiring illustration showing connections for ACC, GND, SWC1, and SWC2. Note that wiring definitions may vary between car stereo brands.

Wiring Steps:

1. Turn off the vehicle's ACC power.
2. Use a crowbar tool to carefully remove the central control panel of your car stereo.
3. Unplug the original power interface from your car stereo.
4. Connect the receiver's transfer cable to the power supply. The receiver typically connects to the car stereo's SWC1 and SWC2 wires. The black wire connects to ground (GND), and the red wire connects to accessory power (ACC).
5. Once connected, check the route of the cables and reinstall the central control panel.

2.2 Mounting the Remote Controls

The remote controls are designed to attach directly to your steering wheel.

Image 2.2: Overview of the installation process, including removing the navigation unit, plugging in the receiver, setting up button learning, and attaching the remote to the steering wheel.

Mounting Steps:

1. The SWC control units have a certain elasticity and are designed to be directly installed on the steering wheel.
2. Adjust the screws on the remote control to securely fix it onto your steering wheel, or place it in a convenient location.

2.3 Button Learning (for Android Car Stereos)

For most Android car stereos, you will need to perform a button learning process. Y-METDRIVING portable car stereos typically do not require this step.

Image 2.3: Example of a car stereo's navigation controller learning interface, where you can assign functions to the remote control buttons.

Learning Steps:

1. Open the vehicle ACC (Accessory power) to power on the car stereo.
2. On your Android car stereo, navigate to the 'Steering Learn' or 'Steering Wheel Control Settings' interface.
3. Clear any existing button settings if prompted.
4. Select a function on the car stereo's screen (e.g., Volume Up).
5. Press and hold the corresponding button on the Y-METDRIVING remote control until the stereo registers the input.
6. Repeat for all desired functions (Volume Down, Next Track, Previous Track, Answer Call, Hang Up, Play/Pause, Mode, Custom).
7. Once all buttons are learned, save the settings on your car stereo.

3. Operating Instructions

Once installed and configured, the remote control allows for easy access to various car stereo functions.

3.1 Basic Functions

• Volume Control: Use the dedicated volume up and down buttons to adjust audio levels.
• Track Navigation: Skip to the next or previous track using the respective buttons.
• Call Management: Answer incoming calls or hang up ongoing calls with the designated buttons.
• Play/Pause: Control media playback with the play/pause button.
• Mode/Source: Toggle between different audio sources or modes (e.g., Radio, Bluetooth, USB) using the 'M' button.
• Custom Button: The star-shaped button can be customized to a function of your choice during the learning process.

4. Maintenance

4.1 Charging the Remote Controls

The remote controls are rechargeable via a Type-C interface. A single charge can last for approximately 3 to 6 months under normal usage.

Image 4.1: The remote control features an enduring battery life, typically lasting 3 to 6 months per charge.

To charge, connect a standard USB Type-C cable (not included) to the charging port on the remote control. The indicator light will show charging status.

5. Troubleshooting

If you encounter issues with your Y-METDRIVING Wireless Steering Wheel Remote Control, consider the following:

• Buttons Not Responding:
  • Ensure the remote controls are charged.
  • Verify that the receiver is correctly connected to the car stereo's SWC wires.
  • Re-perform the button learning process on your car stereo.
  • Check if your car stereo supports steering wheel controls.
• Intermittent Functionality:
  • Ensure there are no obstructions between the remote controls and the receiver.
  • Check for any loose wiring connections to the receiver.
• Physical Fit on Steering Wheel:
  • The clamps are designed for a range of steering wheel thicknesses. If the fit is too loose, you may need to add material (e.g., electrical tape) to the steering wheel for a snug fit. If too tight, the clamps may not fit.

6. Specifications

7. Warranty and Support

Y-METDRIVING is committed to product quality. If you encounter any issues during purchase or use, please contact our customer service team via Amazon Email for assistance. We strive to provide excellent customer support.