Important Safety Information
Please read all instructions carefully before using the Adamson B10 Bed Cooling System. Failure to follow these instructions may result in injury or damage to the product.
- Electrical Safety: Always unplug the unit from the power outlet before cleaning, maintenance, or if it will be unused for an extended period. Do not operate with a damaged cord or plug. Keep the power cord away from heated surfaces.
- Water Handling: Use only distilled water in the reservoir to prevent mineral buildup and ensure optimal performance. Do not overfill the reservoir. Ensure all connections are secure to prevent leaks.
- Unit Placement: Place the cooler unit on a stable, level surface. Ensure it is positioned at the same level or higher than the mattress pad to facilitate proper water circulation. Do not block the air vents on the unit.
- General Use: This product is intended for residential use only. Keep out of reach of children and pets. Do not attempt to disassemble or repair the unit yourself. Contact customer support for assistance.
What's Included
Verify that all the following components are present in your package:
- Adamson B10 Cooler Unit
- Cotton Mattress Pad
- Power Cable
- Spare Drain Plug
- Remote Control
- AAA Battery (for remote)
Setup Instructions
- Unpack Components: Carefully remove all items from the packaging.
- Position the Cooler Unit: Place the Adamson B10 Cooler unit on a flat, stable surface next to your bed. For optimal water flow, ensure the unit is at the same level or slightly higher than the mattress pad.
Image: Proper placement of the cooler unit relative to the mattress pad for efficient water circulation.
- Place the Mattress Pad: Lay the cotton mattress pad directly on your bed. The pad is designed for versatile use and can be oriented horizontally for a Twin bed (75"L x 39"W) or vertically for a Single alignment.
Image: Versatile use of the mattress pad for different bed sizes.
- Connect Hoses: Connect the two hoses extending from the cooler unit to the corresponding ports on the mattress pad. Push firmly until they click into place, ensuring a secure, leak-free connection.
Image: Ensure all parts are installed securely to prevent leaks.
- Fill the Reservoir: Open the reservoir cap on the top of the cooler unit. Fill the reservoir with distilled water up to the 'MAX' fill line. Do not overfill.
- Connect Power: Plug the power cable into the cooler unit, then plug the other end into a standard electrical outlet.
- Install Remote Battery: Open the battery compartment on the remote control and insert the provided AAA battery, observing the correct polarity.
Operating Instructions
Once set up, your Adamson B10 Bed Cooling System is ready for use.
- Power On/Off: Press the power button on the remote control or directly on the cooler unit to turn the system on or off.
- Cooling Function: The system will immediately begin circulating chilled water through the mattress pad, effectively lowering the mattress temperature by 7-12°F.
Image: The water cooling system reduces mattress temperature by 7 to 12°F.
- Adjust Fan Speed: Use the fan speed buttons on the remote control to cycle through the four available fan speeds. Select the speed that provides your desired level of cooling.
- Comfort: The mattress pad is made from 100% cotton, providing a soft and breathable surface. You can sleep directly on the pad or add a mattress topper for additional comfort.
Image: The soft and comfy 100% cotton pad allows you to sleep directly on it or add a topper.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your cooling system.
- Water Tank Cleaning: Empty the water tank and refill with fresh distilled water every 2 weeks. This prevents mineral buildup and maintains hygiene.
- Mattress Pad Drying: After emptying the tank, allow the mattress pad to dry out completely every 2 weeks. This helps prevent mold and odors, ensuring optimal performance.
Image: Empty the tank and dry out the mattress every 2 weeks for optimal performance to prevent smell and mold.
- Filter Cleaning: The internal filter should be cleaned every 2-4 weeks. To clean, remove the filter, rinse it under running water, and then reinsert it into the unit.
- Storage: If you plan to store the unit for an extended period, ensure both the water tank and the mattress pad are completely dry before packing.
Troubleshooting
Refer to this section for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| No Cooling or Weak Cooling | Low water level, improper unit placement, kinked hoses, dirty filter. | Check and refill water reservoir. Ensure cooler unit is level with or higher than the mattress. Straighten any kinked hoses. Clean the internal filter. |
| Water Leaks | Loose hose connections, improperly sealed drain plug, damaged components. | Verify all hose connections are secure. Ensure the drain plug is tightly sealed. Inspect hoses and pad for any visible damage. |
| Unit Not Powering On | Power cable disconnected, faulty outlet, remote battery issue. | Check power cable connection to unit and wall outlet. Test the outlet with another device. Ensure AAA battery in remote is correctly inserted and charged. |
| Unusual Noise | Obstruction in fan, unstable placement, low water level. | Check for any obstructions around the fan vents. Ensure the unit is on a stable, level surface. Verify the water level in the reservoir. |
Specifications
| Brand | Adamson |
| Model Name | Adamson B10 |
| Material | 100% Cotton Pad |
| Mounting Type | Freestanding |
| Special Features | 4 Fan Speeds, Remote Control Included, Water Cooling System |
| Color | Gray |
| Air Flow Capacity | 80 Cubic Feet Per Minute |
| Controls Type | Remote |
| Item Weight | 1.3 Kilograms |
| Recommended Use | Residential |
| Form Factor | Personal |
| Wattage | 8 Watt-hours |
| Noise Level | 30 Decibels |
| Smart Home Compatibility | Not Smart Home Compatible |
| Operation Mode | Automatic |
| Size | Twin (75"L x 39"W) |
| Energy Consumption Standard | 8 Watt Hours |
| Included Components | Adamson B10 Cooler, Cotton Mattress Pad, Power Cable, Spare Drain Plug, Remote Control, AAA Battery |
Warranty and Support
Your Adamson B10 Bed Cooling System is backed by a comprehensive warranty and dedicated customer support.
- Warranty: The product includes a 5-year assurance, covering manufacturing defects and ensuring long-term reliability.
- Customer Support: For any questions, technical assistance, or warranty claims, please contact our 24/7 customer service. Refer to the product packaging or the official Adamson website for contact details.