1. Introduction
Welcome to the world of electric skateboarding with your new MEEPO Campus V5 Series/Envy Electric Skateboard. This manual provides essential information for the safe and optimal operation, maintenance, and care of your skateboard. Please read it thoroughly before your first ride to ensure a safe and enjoyable experience.
Figure 1: MEEPO Campus V5 Series/Envy Electric Skateboard (Top, Side, and Bottom Views)
2. Safety Guidelines
Your safety is paramount. Electric skateboards can reach high speeds and require careful handling. Always adhere to the following safety guidelines:
- Wear Protective Gear: Always wear a helmet, knee pads, elbow pads, and wrist guards.
- Check Your Board: Before each ride, inspect the board for any loose components, wheel damage, or battery issues.
- Understand Your Surroundings: Ride in safe, open areas away from traffic, pedestrians, and obstacles.
- Know Your Limits: Start at low speeds and gradually increase as you become more comfortable.
- Weather Conditions: Avoid riding in wet conditions, heavy rain, or on slippery surfaces.
- Local Laws: Be aware of and comply with all local laws and regulations regarding electric skateboards.
- Age and Weight Limits: This product is suitable for adults and teens. The maximum load capacity is 330 pounds.
3. Package Contents
Upon unboxing your MEEPO Campus V5 Series/Envy Electric Skateboard, please verify that all the following items are included:
- MEEPO Campus V5 Series/Envy Electric Skateboard (NLS3)
- Remote Control
- Charger
- T-Tool (for adjustments)
- Spare Belts (245mm)
- USB Charging Cable for Remote
- User Manual (this document)
Figure 2: Included Components
4. Setup & Assembly
4.1 Initial Inspection
Before your first ride, carefully inspect your skateboard for any signs of damage during shipping. Ensure all screws are tightened and wheels spin freely.
4.2 Charging the Battery
- Connect the charger to the charging port on the skateboard.
- Plug the charger into a standard wall outlet.
- The indicator light on the charger will change (e.g., red to green) when fully charged.
- Charging time is approximately 2 hours for a full charge.
4.3 Remote Control Pairing
Your remote control should be pre-paired. If re-pairing is needed, refer to the specific instructions in the separate remote control manual or the official Meepo website.
4.4 Wheel and Belt Installation/Adjustment
The NLS3 model uses belts for power transmission. Periodically check the tension and condition of these belts. If replacement is necessary, follow the steps demonstrated in the video below. Ensure the wheel is securely fastened after any adjustments or replacements.
Video: How to replace 245mm belts for NLS 3. This video demonstrates the process of removing and installing the drive belts on the MEEPO NLS3 electric skateboard, including loosening and tightening the necessary screws and properly seating the new belt.
5. Operating Your Electric Skateboard
5.1 Getting Started
- Turn on the skateboard and the remote control.
- Ensure the remote is connected to the board (check remote display).
- Place one foot on the board, then push off with the other foot to gain initial momentum.
- Gently push the throttle on the remote to accelerate.
5.2 Remote Control Functions
The N5S Display Remote allows for precise control:
- Throttle: Push forward to accelerate, pull back to brake.
- Speed Modes: Switch between different speed modes (e.g., Beginner, Eco, Pro) to match your skill level and riding environment.
- Display: Shows current speed, battery level (board and remote), and distance traveled.
5.3 Riding Techniques
- Stance: Find a comfortable stance with your feet positioned over the trucks for balance.
- Turning: Lean into turns, similar to a traditional skateboard or snowboard.
- Braking: Apply brakes smoothly to avoid sudden stops. Regenerative braking helps recharge the battery.
Figure 3: Proper Riding Stance
6. Maintenance
Regular maintenance ensures the longevity and performance of your electric skateboard.
6.1 Battery Care
- Charge the battery fully after each use, especially if storing for extended periods.
- Do not overcharge or completely drain the battery.
- Store the board in a cool, dry place, away from direct sunlight and extreme temperatures.
6.2 Cleaning and Storage
- Wipe down the board with a damp cloth after each ride to remove dirt and debris.
- Avoid using harsh chemicals or excessive water, especially near electronic components.
- Store the board indoors in a dry environment.
6.3 Belt and Wheel Maintenance
- Regularly inspect drive belts for wear, cracks, or damage. Replace them as needed (refer to Section 4.4).
- Check wheels for cuts, cracks, or excessive wear.
- Ensure wheel nuts are tightened to prevent wobbling.
- Clean bearings periodically to maintain smooth wheel rotation.
Figure 4: Wheel and Motor Assembly
7. Troubleshooting
If you encounter issues with your MEEPO electric skateboard, refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Board not turning on | Low battery; Power button not pressed correctly | Charge the board; Press and hold the power button firmly |
| Remote not connecting | Remote battery low; Not paired; Interference | Charge remote; Re-pair remote (refer to remote manual); Move away from interference sources |
| Loss of power during ride | Low board battery; Overheating; Loose connection | Charge board; Allow board to cool down; Check all connections |
| Unusual noises from wheels/motors | Debris in motor/belt; Worn bearings; Loose components | Clean motors/belts; Replace bearings; Tighten all screws |
| Reduced range | Battery degradation; Riding style; Terrain | Ensure full charge; Ride in Eco mode; Avoid steep hills or aggressive acceleration |
8. Specifications
Key technical specifications for the MEEPO Campus V5 Series/Envy Electric Skateboard (NLS3):
| Feature | Specification |
|---|---|
| Brand | Meepo |
| Model Name | MB0094 (NLS3) |
| Top Speed | Up to 29 Mph (47 km/h) / 32 Mph (52 km/h) |
| Max Range | Up to 24 Miles (38 km) |
| Battery | 12S2P MolicelP42A, 362WH (8.4AH) |
| Charging Time | Approx. 2 hours (with 4.5A fast charging) |
| Motors | 2 x 2519W (HB-4240) |
| ESC | Hobbywing ESC (HB-9028-36A) |
| Deck Material | Pure Bamboo + Fiberglass (8 Ply) |
| Deck Length | 38.9 Inches (980mm) |
| Deck Width | 12.2 Inches (254mm) |
| Item Weight | 9.7 Kilograms |
| Load Capacity | 330 Pounds |
| Wheel Size | 90 Millimeters |
| Trucks | 8-inch RKP (Reverse Kingpin) |
| Water Resistance | IPX5 (Splash resistant, not submersible) |
Figure 5: Skateboard Components and Performance Overview
9. Warranty and Support
9.1 Warranty Information
Your MEEPO Campus V5 Series/Envy Electric Skateboard comes with a limited warranty. Please refer to the official Meepo website or contact customer support for detailed warranty terms and conditions. The warranty period is typically 6 months from the date of purchase.
9.2 Customer Support
For any questions, technical assistance, or warranty claims, please contact Meepo customer support:
- Official Website: www.meepoboard.com
- Email: info@meepoboard.com
- Live Chat: Available on the official website.
- Address: G/f Hang Wai Indctmo 6 Kin Tai St Tuen Mun Nt Hong Kong
Meepo is committed to providing high-quality products and excellent customer service. Your satisfaction is our priority.
