Introduction
The e-vibra V5 Silent Vibrating Alarm Watch is designed to provide discreet reminders throughout the day. This device is ideal for various uses, including potty training, medication reminders, hydration alerts, and maintaining a daily schedule without disturbing others. Its slim, lightweight design and soft silicone wristband ensure comfort and ease of use.
Figure 1: e-vibra V5 Potty Training Watch displaying 5:30 PM.
Product Features
- Safety Tested Design: Features a soft-silicone wristband, designed to fit wrists approximately 3.9" - 7.5" (10cm - 19cm).
- Countdown Interval Timer: Set alarms for intervals of 1, 5, 10, 15, 20, 30, 45, 60, 90 minutes, 2 hours, or 3 hours. The auto-repeating vibration reminds you for tasks like potty breaks or drinking water.
- Strong Vibrating Alarm: Provides a silent yet strong vibration for discreet reminders, suitable for potty training, medication, hydration, or daily scheduling.
- Wake-Up Alarm: Set specific alarm times (e.g., 5:55 AM or 7:12 AM) to wake up without disturbing others.
- Long Battery Life: One full charge can last between 7 to 20 days, depending on usage.
- Power-Off Memory: Retains all alarm settings even after the device is powered off.
Setup
- Initial Charging: Before first use, fully charge the watch. Refer to the 'Charging' section for detailed instructions.
- Assemble the Watch (if necessary): If the watch module is separate from the band, gently push the module into the silicone wristband until it is securely seated. Ensure the display faces outwards.
- Adjusting the Wristband: Place the watch on the wrist and adjust the buckle to a comfortable and secure fit. The band is designed to fit a wide range of wrist sizes.
- Power On: Press and hold the button on the side of the watch until the display illuminates.
Figure 2: Watch module and silicone band components.
Operating Instructions
The e-vibra V5 watch features a single button for navigation and setting adjustments. Short presses typically cycle through modes or increase values, while long presses confirm selections or enter setting modes.
Figure 3: Close-up of the watch display showing time and alarm indicator.
Setting Time and Date
- From the main time display, press and hold the button until the hour digits begin to flash.
- Short press the button to adjust the hour.
- Press and hold the button to move to minute adjustment. Short press to adjust minutes.
- Repeat this process for setting the date (month, day, year) if applicable to your model.
- Press and hold to exit time/date setting mode.
Setting Alarms (Specific Times)
The watch supports up to 15 silent vibrating alarms.
- From the main time display, short press the button until you see the alarm setting interface (often indicated by an alarm icon).
- Press and hold the button to enter alarm setting mode. The alarm number (e.g., A1) will appear, followed by flashing hour digits.
- Short press to adjust the hour for the current alarm.
- Press and hold to move to minute adjustment. Short press to adjust minutes.
- Press and hold to save the alarm and move to the next alarm slot (A2, A3, etc.).
- To enable/disable an alarm, cycle through the alarms. When an alarm time is displayed, a short press may toggle it on/off (indicated by an icon).
- Exit alarm setting by pressing and holding until the display returns to the main time.
Setting Countdown Interval Timer
This feature provides repeating vibrations at set intervals.
- From the main time display, short press the button until you reach the countdown timer interface (often indicated by a timer icon).
- Press and hold the button to enter timer setting mode. The current interval will flash.
- Short press the button to cycle through available intervals: 1min, 5min, 10min, 15min, 20min, 30min, 45min, 60min, 90min, 2 hours, 3 hours.
- Once your desired interval is displayed, press and hold the button to confirm and start the timer. The watch will vibrate at the end of each interval and automatically reset.
- To stop the interval timer, press and hold the button again while the timer is active.
Stopping a Vibration
When the watch vibrates for an alarm or interval, a short press of the button will stop the vibration. For interval timers, the timer will automatically restart for the next interval.
Video 1: Demonstration of e-vibra Potty Training Watch features and operation. This video shows basic functions and how to set alarms.
Video 2: Detailed guide on using the e-vibra watch for medical and general reminders.
Charging
The e-vibra V5 watch is rechargeable via a standard USB port. A full charge provides extended use, typically 7-20 days depending on the frequency of vibrations.
- Locate the USB charging port on the watch module. This is usually found by gently pulling one side of the watch module out of the silicone band to reveal the USB connector.
- Insert the watch's USB connector directly into any standard USB power source (e.g., computer USB port, USB wall adapter, power bank).
- The display will show a charging indicator. Once fully charged, the indicator may change or turn off.
- After charging, carefully reinsert the watch module into the silicone band.
Figure 4: Instructions for USB charging the e-vibra V5 watch.
The watch features power-off memory, meaning your alarm and timer settings will be retained even if the battery fully depletes or the device is powered off.
Maintenance
- Cleaning: Wipe the watch and band with a soft, damp cloth. Avoid using harsh chemicals or abrasive materials.
- Water Resistance: The watch is rated as "Water Resistant." This typically means it can withstand splashes, rain, and brief exposure to water. It is not recommended for swimming, showering, or submersion in water, as this may cause damage.
- Storage: Store the watch in a cool, dry place when not in use.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Watch not charging | Improper USB connection; faulty USB port/cable; depleted battery. | Ensure the watch module is fully inserted into a working USB port. Try a different USB port or cable. Allow a few minutes for the charging indicator to appear if the battery is completely drained. |
| Watch continuously vibrates | Software glitch; internal malfunction. | Try pressing and holding the button to attempt a reset. If the issue persists, contact customer support. |
| Display is blank or not working | Battery is low or dead; watch is off; internal damage. | Charge the watch. Press the button to wake the display. If charging does not resolve the issue, contact customer support. |
| Alarms/Timers not activating | Alarms/Timers are not set correctly or are disabled. | Review the 'Operating Instructions' section to ensure alarms and timers are set and enabled properly. |
Specifications
| Feature | Detail |
|---|---|
| Brand Name | e-vibra |
| Model Name | V5 |
| Model Number | V5C |
| Display Type | Digital |
| Watch Movement Type | Quartz |
| Strap Type | Two Piece Strap |
| Clasp Type | Buckle |
| Water Resistance Level | Water Resistant |
| Band Color | Black |
| Dial Color | Black |
| Face Style | Minimalist |
| Item Weight | 17.01 g |
| Unit Count | 1 Count |
| Manufacturer | e-vibra |
| UPC | 880034268498 |
| Band Material Type | Silicone |
| Case Material Type | Silicone |
| Crystal | Glass |
Warranty and Support
e-vibra is committed to customer satisfaction. If you encounter any issues with your V5 Potty Training Watch, please contact the manufacturer directly. Many customers have reported positive experiences with their responsive customer service for replacements or troubleshooting assistance.
For support, please refer to the contact information provided with your product packaging or visit the official e-vibra website.