SilverStone NovaPeak 360 ARGB All-in-one Liquid Cooler User Manual

1. Introduction

Thank you for choosing the SilverStone NovaPeak 360 ARGB All-in-one Liquid Cooler. This product is designed to provide efficient and reliable cooling for your CPU, featuring advanced pump technology, high-performance fans, and customizable ARGB lighting effects. This manual provides essential information for the proper installation, operation, and maintenance of your liquid cooler.

Safety Precautions

• Always disconnect power from your computer before installation or maintenance.
• Handle components with care to avoid damage.
• Keep out of reach of children.
• Do not open the liquid loop; it is factory-sealed and contains coolant.
• Ensure proper grounding to prevent electrostatic discharge (ESD) damage.

2. Package Contents

Please verify that all components are present before beginning installation. If any items are missing or damaged, please contact your retailer or SilverStone support.

• NovaPeak 360 ARGB Radiator with Integrated Pump/Cold Plate
• 3 x 120mm ARGB Radiator Fans
• Intel Mounting Kit (LGA115x/1200/1700/1851/2011/2066)
• AMD Mounting Kit (AM5/AM4)
• Thermal Paste (pre-applied or tube)
• ARGB Controller (if not motherboard sync compatible)
• Fan Screws and Mounting Hardware
• User Manual

Overall view of the NovaPeak 360 ARGB liquid cooler, showing the radiator, three ARGB fans, and the pump/cold plate assembly.

3. Specifications

Detailed technical specifications for the NovaPeak 360 ARGB liquid cooler:

4. Installation Guide

This section outlines the general steps for installing the NovaPeak 360 ARGB liquid cooler. Specific steps may vary slightly depending on your motherboard and PC case. Refer to your motherboard and case manuals for detailed instructions.

4.1 Prepare Your System

1. Power off your computer and unplug it from the wall outlet.
2. Open your PC case and remove any existing CPU cooler. Clean the CPU surface thoroughly to remove old thermal paste.
3. Identify the appropriate mounting hardware for your CPU socket (Intel or AMD).

4.2 Install Radiator Fans

1. Attach the three 120mm ARGB fans to the radiator using the provided fan screws. Ensure the fan airflow direction is as desired (typically pushing air through the radiator or pulling air through it, depending on case airflow).
2. Connect the fan PWM cables and ARGB cables. The NovaPeak series features a modular cabling design for simplified connections.

Close-up of the modular cabling connection point on the NovaPeak radiator fan, illustrating the simplified wiring.

Illustration of the streamlined connectivity for effortless cable management, demonstrating the daisy-chain cabling of the fans.

4.3 Mount Radiator

1. Mount the radiator assembly into your PC case in an appropriate 360mm fan mounting location (e.g., front, top). Secure it with the provided screws.

4.4 Install Pump/Cold Plate

1. Apply thermal paste to the center of your CPU's integrated heat spreader (IHS) if it's not pre-applied on the cold plate. A pea-sized dot or a thin line is usually sufficient.
2. Carefully place the pump/cold plate assembly onto the CPU, aligning it with the mounting holes.
3. Secure the pump/cold plate using the appropriate Intel or AMD mounting brackets and screws. Tighten screws in a cross pattern until snug, ensuring even pressure.

Detailed view of the copper baseplate of the NovaPeak liquid cooler, designed for optimal contact with the CPU.

Visual explanation of the slightly-convexed copper baseplate, emphasizing its firm contact with the processor.

4.5 Connect Cables

1. Connect the pump's 4-pin power cable to the CPU_FAN or AIO_PUMP header on your motherboard. Ensure it receives full power (often set to 100% in BIOS).
2. Connect the fan PWM cables to your motherboard's fan headers or a fan hub.
3. Connect the ARGB cables to your motherboard's 5V ARGB header or the included ARGB controller.

Close-up of the NovaPeak pump block with its ARGB lighting effects active, displaying the snowflake logo.

Internal diagram of the high-reliability pump motor, showing its three-phase, six-pole design for smoother and quieter operation.

4.6 Final Checks

1. Ensure all cables are securely connected and routed neatly to avoid interference with moving parts.
2. Close your PC case.
3. Reconnect power and boot your system.

5. Operation

Once installed, the NovaPeak 360 ARGB liquid cooler operates automatically based on your system's thermal load and fan/pump speed settings.

5.1 Fan and Pump Control (PWM)

The fans and pump are PWM (Pulse Width Modulation) controlled, allowing your motherboard to dynamically adjust their speed based on CPU temperature. This ensures optimal cooling performance while minimizing noise when the system is idle or under light load.

• Access your motherboard's BIOS/UEFI settings to configure fan curves for the CPU_FAN/AIO_PUMP headers.
• Ensure the pump header is set to run at full speed (100%) for consistent coolant flow.

Diagram illustrating the efficient heat dissipation performance of the NovaPeak radiator fans, including a fan speed vs. duty cycle graph.

5.2 ARGB Lighting Control

The NovaPeak 360 ARGB features addressable RGB lighting on both the pump and fans, allowing for extensive customization.

• Motherboard Sync: If connected to a compatible 5V ARGB header on your motherboard, you can control lighting effects using your motherboard manufacturer's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync).
• ARGB Controller: If your motherboard lacks an ARGB header or you prefer standalone control, use the included ARGB controller to cycle through various lighting modes, adjust brightness, and change speed.

Individual NovaPeak ARGB fan showcasing its vibrant lighting effects and transparent blades.

6. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your liquid cooler.

• Dust Cleaning: Periodically clean dust from the radiator fins and fan blades using compressed air or a soft brush. Excessive dust buildup can impede airflow and reduce cooling efficiency.
• Check Connections: Occasionally inspect all cable connections (power, PWM, ARGB) to ensure they are secure.
• Liquid Loop: The liquid loop is factory-sealed and requires no user maintenance or refilling. Do not attempt to open or modify the tubing or pump.

7. Troubleshooting

If you encounter issues with your NovaPeak 360 ARGB liquid cooler, refer to the following common problems and solutions:

7.1 High CPU Temperatures

• Check Pump Connection: Ensure the pump's power cable is securely connected to the CPU_FAN or AIO_PUMP header and is receiving full power (100% speed) in BIOS.
• Verify Cold Plate Contact: Ensure the cold plate is making firm and even contact with the CPU. Re-seat the cooler if necessary, applying new thermal paste.
• Fan Operation: Check if all fans are spinning. Ensure fan cables are properly connected to PWM headers.
• Airflow: Verify that the radiator fans are installed correctly for optimal airflow within your case. Clean any dust buildup on the radiator fins.

7.2 Fans Not Spinning or ARGB Not Lighting Up

• Power Connections: Ensure all fan PWM cables and ARGB cables are securely connected to the motherboard headers or the ARGB controller.
• ARGB Header: Verify that the ARGB header on your motherboard is enabled in BIOS and that the correct software is being used for control.
• Controller Functionality: If using the ARGB controller, ensure it is powered and functioning correctly. Try cycling through modes.

7.3 Unusual Noises

• Fan Noise: Check for any cables obstructing fan blades. Ensure fan screws are tightened. Adjust fan curves in BIOS to reduce speed at idle.
• Pump Noise: A slight hum from the pump is normal. Excessive gurgling or grinding might indicate air bubbles. Gently tilt your PC case to help move air bubbles to the radiator. Ensure the pump is mounted lower than the highest point of the radiator.

8. Warranty and Support

SilverStone Technology provides a limited warranty for the NovaPeak 360 ARGB liquid cooler against defects in materials and workmanship. The warranty period and terms may vary by region. Please retain your proof of purchase for warranty claims.

Technical Support

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please visit the official SilverStone Technology website for contact information and support resources.

Website: www.silverstonetek.com