Important Safety Information
Please read these instructions carefully before installing or operating this fixture. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause injury or property damage.
- Always disconnect power at the main circuit breaker before installation, maintenance, or bulb replacement.
- All wiring connections must be in accordance with local and national electrical codes. If you are unfamiliar with proper electrical wiring connections, consult a qualified electrician.
- This fixture is rated for damp locations for covered outdoor use. Do not expose to direct water spray or submersion.
- Ensure the mounting surface can support the weight of the fixture (approximately 13 lbs).
- Use only the specified bulb type and wattage.
What's in the Box
Carefully unpack the fixture and check that all parts are included. Keep the packaging materials until you are sure all parts are present and the fixture is working correctly.
- Pendant Light Fixture
- 72-inch Chain
- Ceiling Canopy
- Mounting Hardware (screws, wire nuts, etc.)
Setup and Installation
Before beginning installation, ensure the power is turned off at the circuit breaker. It is recommended to have a second person assist with installation due to the fixture's weight and size.
Tools Required (Not Included):
- Phillips Head Screwdriver
- Flat Head Screwdriver
- Wire Strippers
- Pliers
- Electrical Tape
- Ladder
Step-by-Step Installation:
- Turn Off Power: Locate the circuit breaker controlling the light fixture's power supply and turn it off. Verify power is off using a voltage tester.
- Prepare Mounting Surface: If replacing an existing fixture, remove it. Ensure the junction box is securely mounted and capable of supporting the fixture's weight.
- Attach Mounting Bracket: Secure the mounting bracket (usually included with the canopy) to the junction box using the provided screws.
- Adjust Chain Length: Determine the desired hanging height for the fixture. Use pliers to open and remove excess chain links from the 72-inch chain. Thread the fixture's electrical wire through the chain and the canopy.
- Make Electrical Connections:
- Connect the fixture's black wire to the house's black (hot) wire.
- Connect the fixture's white wire to the house's white (neutral) wire.
- Connect the fixture's ground wire (bare copper or green) to the house's ground wire and the mounting bracket's ground screw.
- Secure all connections with wire nuts and wrap with electrical tape for added safety.
- Mount Canopy: Carefully push the wired canopy up to the ceiling, aligning the canopy screws with the holes in the mounting bracket. Secure the canopy in place.
- Install Light Bulb: Insert one E26 base, 60-watt maximum incandescent or equivalent LED bulb (not included) into the socket.
- Restore Power: Turn the power back on at the circuit breaker. Test the fixture.
Diagram illustrating the dimensions of the pendant light: 19 1/2 inches high, 10 inches wide, with a 5-inch canopy diameter.
Detailed view of the black ceiling canopy and the chain connection point, showing the secure mounting mechanism.
The John Timberland Cecile outdoor pendant light fixture, shown as if installed, with its chain and canopy.
Operating Instructions
This fixture operates using a standard wall switch (not included). Ensure the correct bulb is installed for proper function.
Turning On/Off:
Use the connected wall switch to turn the light fixture on or off.
Bulb Replacement:
To replace the bulb, first ensure the power is turned off at the circuit breaker. Allow the old bulb to cool completely before removing it. Unscrew the old bulb and screw in a new E26 base, 60-watt maximum incandescent or equivalent LED bulb. Do not exceed the maximum wattage.
Maintenance
Regular maintenance will help preserve the appearance and functionality of your light fixture.
Cleaning:
- Always turn off power before cleaning.
- Wipe the fixture with a soft, damp cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish or glass.
- For the clear seeded glass, a mild glass cleaner can be used, applied to a cloth first, not directly to the fixture.
Bulb Care:
Replace bulbs as needed following the 'Bulb Replacement' instructions in the Operating section. Ensure bulbs are clean and free of debris for optimal light output.
Troubleshooting
If you experience issues with your fixture, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | 1. Power is off. 2. Bulb is loose or burnt out. 3. Wiring connections are faulty. | 1. Check circuit breaker and wall switch. 2. Tighten or replace bulb. 3. Turn off power and check wiring connections. Consult an electrician if unsure. |
| Light flickers. | 1. Loose bulb. 2. Loose wiring connection. 3. Incorrect bulb type. | 1. Tighten bulb. 2. Turn off power and check wiring connections. 3. Ensure bulb is E26 base, 60W max. |
| Glass panels appear dirty or cloudy. | Accumulated dust or residue. | Clean glass panels with a soft cloth and mild glass cleaner. |
Specifications
| Brand | John Timberland |
| Model Number | 7341E |
| Dimensions (H x W x D) | 19.5" x 10" x 10" |
| Chain Length | 72 inches (adjustable) |
| Canopy Diameter | 5 inches |
| Weight | 13 lbs |
| Bulb Type | E26 Medium Base (bulb not included) |
| Max Wattage | 60 watts |
| Voltage | 120 Volts |
| Material | Metal frame, Clear Seeded Glass panels |
| Finish | Painted Black |
| Indoor/Outdoor Usage | Outdoor (Damp Location Rated for covered use) |
| Power Source | Hardwired |
Warranty Information
This John Timberland fixture comes with a limited 1-year warranty from the manufacturer. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
Customer Support
If you have any questions regarding the installation, operation, or maintenance of your John Timberland Cecile outdoor pendant light fixture, please contact the retailer or manufacturer's customer service department. For electrical issues, it is always recommended to consult a qualified electrician.
Product Overview
Front view of the John Timberland Cecile outdoor pendant light fixture, showcasing its black finish and clear seeded glass panels.
An angled perspective of the John Timberland Cecile outdoor pendant light, highlighting the rustic design and glass texture.
Frontal view of the pendant light, emphasizing the clear seeded glass and the visible light bulb inside.
Detailed image of the black chain connecting to the top of the light fixture, showing the link design.
Official Product Video
This video provides a general overview of the John Timberland brand and its product offerings. While not specific to installation, it showcases the brand's style and quality.