1. Introduction
This manual provides instructions for the proper use and maintenance of Shootingstar 24 Pack Refill Glue Cards. These cards are designed to be used with compatible indoor flying insect traps, specifically the LiBa FT06 model, to effectively capture various flying insects.
2. Compatibility
The Shootingstar Refill Glue Cards are specifically designed to be compatible with the LiBa FT06 Flying Insect Trap. They may also be compatible with other similar indoor flying insect traps that utilize a comparable glue board design.
Image: The refill glue card shown next to a LiBa FT06 Flying Insect Trap, illustrating compatibility.
3. Features
- Effective Insect Trapping: The glue boards are designed with a super sticky surface to effectively trap mosquitoes, fruit flies, gnats, moths, and other small flying insects.
- Non-Toxic and Odorless: These glue cards are non-toxic and produce no smell, making them suitable for indoor use in various living spaces.
- Long-Lasting: Each replacement card can remain effective for up to 2 weeks, depending on the insect activity in the area.
Image: Illustration showing the types of insects effectively trapped by the glue cards, including moths, mosquitoes, flies, and fruit flies.
Image: A family in a home setting, emphasizing the non-toxic and odorless nature of the glue cards for safe indoor environments.
4. Setup and Installation
Follow these steps to install a new refill glue card into your compatible insect trap:
- Carefully remove the new glue card from its packaging.
- Peel off the protective plastic cover from the adhesive side of the glue card. Ensure the adhesive side is exposed.
- Insert the exposed glue card into the designated slot of your indoor insect trap (e.g., LiBa FT06). Make sure the adhesive surface faces outwards or towards the light source of the trap, and that it does not adhere to the internal components of the trap itself.
- Ensure the card is securely seated within the trap.
Image: Visual instructions demonstrating how to peel the protective cover, insert the card into the trap, and dispose of a used card.
5. Operating Instructions
Once the glue card is installed in the insect trap, plug the trap into an electrical outlet in an area where flying insects are observed. The trap's light will attract insects, which will then become stuck to the adhesive surface of the glue card. For optimal results, place the trap in areas prone to insect activity, such as kitchens, living rooms, bedrooms, or near entry points.
Image: A collage showing various indoor locations like a kitchen, living room, bedroom, and balcony, indicating suitable places for trap placement.
6. Maintenance and Replacement
The refill glue cards are designed for single use and should be replaced regularly to maintain effectiveness. It is recommended to replace the glue card every 2 weeks, or sooner if it becomes full of insects or loses its stickiness. To replace, simply unplug the trap, carefully remove the old, used card, and dispose of it responsibly. Then, follow the installation steps (Section 4) to insert a new card.
Image: An illustration displaying multiple refill glue cards, highlighting the availability of a 24-pack for continuous use.
7. Troubleshooting
- Insects not being trapped: Ensure the plastic cover has been fully removed from the glue card. Verify the trap is plugged in and its light is functioning. Consider relocating the trap to an area with higher insect activity.
- Card not fitting correctly: Double-check that you are using the correct refill card model for your insect trap. Ensure the card is inserted in the correct orientation.
- Card losing stickiness prematurely: High humidity or dusty environments can reduce stickiness. Ensure the trap is placed in a suitable environment and replace the card if necessary.
8. Specifications
| Attribute | Value |
|---|---|
| Product Name | Refill Glue Card |
| Compatibility | LiBa FT06 Flying Insect Trap and similar models |
| Quantity | 24 Count |
| Recommended Replacement Interval | Up to 2 weeks |
| Target Species | Mosquitoes, Fruit Flies, Gnats, Moths, other small flying insects |
| Material | Adhesive-coated paper |
| Package Dimensions | 3.98 x 2.72 x 0.67 inches |
| Item Weight | 2.39 ounces (0.07 Kilograms) |
9. Safety Information
- Keep out of reach of children and pets to prevent accidental contact with the sticky surface.
- Avoid touching the adhesive surface directly. If contact occurs, wash hands with soap and water.
- Do not place near open flames or heat sources.
- Dispose of used glue cards in a sealed bag to prevent insects from escaping and to maintain hygiene.
10. Support
If you have any questions, concerns, or require assistance with your Shootingstar Refill Glue Cards, please do not hesitate to contact us. We are committed to providing a satisfying solution to our customers.
For support, please visit the Shootingstar Store on Amazon or contact customer service through your purchase platform.