Introduction
Thank you for choosing the JoFomp 12-Inch Silent LED Night Light Wall Clock. This clock features a silent quartz movement, an integrated LED night light with automatic brightness adjustment, and multiple power options. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal performance.

Figure 1: JoFomp 12-Inch Wall Clock (Unilluminated)
Package Contents
- 1 x JoFomp 12-Inch Silent LED Night Light Wall Clock
- 1 x USB Power Cable
- 1 x Instruction Manual (this document)
Note: AA batteries are not included and must be purchased separately.
Setup
1. Battery Installation
The clock requires two sets of batteries for independent functions:
- For Clock Movement: Insert 1 "AA" battery into the designated compartment for the timekeeping mechanism.
- For LED Light Effect: Insert 3 "AA" batteries into the compartment for the LED lighting. Alternatively, the LED light can be powered via the included USB cable.
Important: Avoid using high-energy alkaline batteries for the clock movement, as their high current may damage the quartz mechanism. Carbon dry batteries are recommended to extend the clock's lifespan.
2. USB Power Connection (for LED Light)
If you prefer not to use batteries for the LED light, connect the provided USB cable to the Type-C port on the back of the clock and plug the other end into a compatible USB power adapter (not included).

Figure 2: Type-C USB Port for LED Power
3. Mounting
The clock is designed for wall mounting. Use the integrated hook on the back of the clock to securely hang it on a wall nail or screw.

Figure 3: Clock Components and Rear View
Operating Instructions
1. Setting the Time
Turn the adjustment knob located on the back of the clock's movement mechanism to set the correct time. Ensure the minute and hour hands are aligned accurately.
2. LED Night Light Control
On the back of the clock, locate the slide switch for the LED light control. It has three modes:
- OFF: Turns off the LED light effect.
- AUTO: Activates the automatic light sensing feature. The LED light will turn on and adjust its brightness intelligently based on ambient light levels.
- ON: Keeps the LED light on continuously, regardless of ambient light.

Figure 4: LED Light Mode Switch
3. Brightness Adjustment (in ON or AUTO mode)
When the LED light is in "ON" or "AUTO" mode, you can adjust its brightness using the "BRIGHTNESS" slider control on the back of the clock. Slide it towards "+" for increased brightness or towards "-" for decreased brightness.

Figure 5: Brightness Adjustment Slider

Figure 6: Visual Representation of Brightness Adjustment

Figure 7: Automatic Light Sensing Function
Maintenance
1. Battery Replacement
When the clock hands stop moving or the LED light dims significantly (and is not due to brightness settings or USB power), it is time to replace the batteries. Follow the battery installation steps in the Setup section.
2. Cleaning
To clean the clock, gently wipe the surface with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these may damage the finish or the clock face.
Troubleshooting
- Clock is not keeping accurate time:
- Ensure the "AA" battery for the clock movement is fresh and correctly installed.
- Verify that a carbon dry battery is used for the clock movement, not an alkaline battery.
- LED light is not turning on or is too dim:
- Check the 3 "AA" batteries for the LED light; ensure they are fresh and correctly installed.
- If using USB power, ensure the USB cable is securely connected and the power adapter is functioning.
- Verify the LED light control switch is set to "ON" or "AUTO".
- Adjust the "BRIGHTNESS" slider to increase the light intensity.
- If in "AUTO" mode, ensure the ambient light is low enough for the sensor to activate the LED.
- Clock is making ticking sounds:
- The JoFomp wall clock features a silent quartz movement. If ticking is heard, ensure the clock is securely mounted and not vibrating against the wall. If the issue persists, contact customer support.
Specifications
| Brand | JoFomp |
| Model Number | 081239-LED |
| Color | Warm Light |
| Display Type | Analog |
| Special Feature | Silent Clock, LED Night Light, Auto-Dimming |
| Product Dimensions | 12"W x 12"H |
| Power Source | 1 x AA Battery (for clock movement), 3 x AA Batteries OR USB Cable (for LED light) |
| Frame Material | Plastic |
| Item Weight | 1.94 pounds (0.88 Kilograms) |

Figure 8: Quartz Movement Detail
Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact JoFomp customer service directly. Contact details are typically available on the manufacturer's website or through your purchase platform.