XCZAP 027201

Download PDF
Contents

XCZAP Waterproof LED Digital Watch Model 027201 Instruction Manual

Introduction

This manual provides comprehensive instructions for the XCZAP Waterproof LED Digital Watch, Model 027201. This digital watch features a chronograph, alarm, 12/24 hour display, date, day of the week, and LED backlight. Please read this manual carefully to ensure proper use and maintenance of your watch.

XCZAP Digital Watch on a wrist

Image: The XCZAP Digital Watch displayed on a wrist, showing its design and digital display.

Watch Components

Familiarize yourself with the buttons and display of your watch:

  • LIGHT Button: Activates the LED backlight.
  • MODE Button: Cycles through different modes (Time, Alarm, Chronograph).
  • RESET Button: Used for resetting values during setting or chronograph.
  • START Button: Used for starting/stopping functions or adjusting values during setting.
Close-up of watch dial with button labels

Image: A close-up view of the watch dial, highlighting the "LIGHT", "START", "MODE", and "RESET" button labels around the bezel.

Setup and Time Setting

To set the time and date on your XCZAP digital watch:

  1. From the normal time display, press the MODE button three times to enter time setting mode. The seconds digits will flash.
  2. Press the RESET button to cycle through the setting options: Seconds → Hours → Minutes → Month → Date → Day of Week.
  3. While a digit is flashing, press the START button to adjust the value. Hold the START button to increase values quickly.
  4. To switch between 12-hour and 24-hour format, press the RESET button until the hour digits are flashing, then press START to toggle.
  5. Once all settings are adjusted, press the MODE button to return to the normal time display.

Operating Functions

Alarm Setting

  1. From the normal time display, press the MODE button twice to enter alarm setting mode. The hour digits will flash.
  2. Press the RESET button to select between setting hours or minutes.
  3. Press the START button to adjust the flashing value.
  4. Press the MODE button to confirm and exit alarm setting.
  5. To activate/deactivate the alarm, press the RESET button while in alarm mode (after pressing MODE twice). An alarm icon will appear/disappear on the display.

Chronograph (Stopwatch)

  1. From the normal time display, press the MODE button once to enter chronograph mode. The display will show "00:00:00".
  2. Press the START button to begin timing.
  3. Press the START button again to pause timing.
  4. Press the RESET button to reset the chronograph to "00:00:00" while it is paused.
  5. Press the MODE button to exit chronograph mode and return to normal time display.

LED Backlight

Press the LIGHT button at any time to illuminate the display for a few seconds, improving visibility in low-light conditions.

Maintenance

Proper care will extend the life of your watch:

  • Water Resistance: This watch is 3ATM (30 meters) water resistant, suitable for daily water splashes like hand washing. It is not suitable for showering, bathing, swimming, or diving. Avoid pressing buttons underwater.
  • Cleaning: Wipe the watch with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, followed by drying.
  • Storage: Store the watch in a cool, dry place away from direct sunlight and extreme temperatures.
  • Battery: The watch uses a standard watch battery. Battery replacement should be performed by a qualified technician to maintain water resistance.
Water resistance chart for 30M watch

Image: A diagram illustrating the 30M water resistance rating, showing suitability for hand washing but not for showering, swimming, or diving.

Person washing hands while wearing the watch

Image: A person washing hands, demonstrating the watch's suitability for daily water splashes.

Troubleshooting

If you encounter issues with your watch, refer to the following common solutions:

  • Display is blank or dim: The battery may be low or depleted. Replace the battery.
  • Buttons are unresponsive: Ensure the watch is not in a locked mode (if applicable, though this model does not specify one). Try pressing the buttons firmly. If the issue persists, a battery reset (by removing and reinserting the battery) might be necessary, but this should be done by a professional.
  • Time is inaccurate: Re-set the time following the "Setup and Time Setting" instructions. If inaccuracy persists after setting, the battery may be weak or the movement may require service.
  • Water inside the watch: If moisture appears inside the watch, stop using it immediately and have it inspected by a professional. This indicates a breach in the water resistance seal.

Specifications

Detailed product specifications diagram

Image: A technical diagram showing the dimensions and key specifications of the watch.

Product Specifications
Model Number027201
Movement TypeDigital, Japanese Quartz
Case MaterialRubber, Alloy
Band MaterialPU, Silicone
Dial Diameter38 mm / 1.49 in
Case Thickness12 mm / 0.47 in
Band Width16 mm / 0.62 in
Band Length225 mm / 8.85 in
Water Resistance30 Meters (3 ATM)
FunctionsLED Light, Chronograph, Alarm, 12/24 Hour, Date, Week, Stopwatch
Weight17 Grams / 0.6 ounces

Warranty and Support

This XCZAP watch comes with a limited warranty. For specific warranty details or technical support, please refer to the product packaging or contact your retailer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.