Introduction
Thank you for choosing the Z-Lite 1011-18W-BN-LED Harrison Vanity Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.
Image: Z-Lite 1011-18W-BN-LED Harrison Vanity Light in Brushed Nickel.
Safety Information
WARNING: Risk of electric shock. Disconnect power at the circuit breaker or fuse box before installation or servicing. All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC).
- Consult a qualified electrician if you are unsure about the installation process.
- Ensure the fixture is properly grounded.
- Do not install this fixture in wet locations. It is designed for indoor use only.
- Handle the fixture with care to avoid damage to the LED components or glass.
- Proposition 65 Warning: This product may expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Package Contents
Carefully unpack your fixture and inspect for any damage. Keep all packaging materials until you are sure all parts are present and in good condition.
- Harrison Vanity Light Fixture
- Mounting Hardware Kit (mounting plate, screws, wire nuts)
- Instruction Manual
Installation Instructions
Before You Begin
- Turn off the electrical power at the main fuse box or circuit breaker.
- Remove the old fixture (if applicable) and its mounting hardware.
- Carefully unpack the new fixture and lay out all parts on a clean, flat surface.
Mounting the Fixture
- Attach the mounting plate to the junction box using the provided mounting screws. Ensure the plate is securely fastened.
- Connect the electrical wires:
- Connect the bare copper or green ground wire from the fixture to the ground wire from the junction box (usually bare copper or green). Secure with a wire nut.
- Connect the white wire from the fixture to the white (neutral) wire from the junction box. Secure with a wire nut.
- Connect the black wire from the fixture to the black (hot) wire from the junction box. Secure with a wire nut.
- Carefully tuck all wires into the junction box.
- Align the fixture with the mounting plate and secure it using the provided fixture screws.
- Restore power at the circuit breaker and test the fixture.
Image: Dimensional diagram of the Z-Lite Harrison Vanity Light.
Operating Instructions
Once installed, the Z-Lite Harrison Vanity Light operates like any standard wall-mounted light fixture. Simply use the wall switch connected to the fixture to turn it on or off. This fixture uses integrated LED lighting, which does not require bulb replacement.
Care and Maintenance
To maintain the appearance and performance of your Z-Lite Harrison Vanity Light, follow these simple guidelines:
- Cleaning: Always disconnect power before cleaning. Use a soft, dry cloth to wipe the fixture. Avoid abrasive cleaners, solvents, or polishes as they may damage the finish or LED components.
- LED Care: The integrated LED light source is designed for long-lasting performance and does not require replacement. Do not attempt to disassemble or replace the LED components.
Troubleshooting
If your fixture is not functioning correctly, refer to the table below for common issues and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. | Check circuit breaker or fuse. Ensure wall switch is in the 'ON' position. |
| Loose wire connections. | Turn off power, check all wire connections for tightness. | |
| Fixture is flickering. | Loose wire connections. | Turn off power, check all wire connections for tightness. |
| Incorrect dimmer switch. | Ensure you are using an LED-compatible dimmer switch if applicable. |
Product Specifications
| Feature | Detail |
|---|---|
| Model Name | 1011-18W-BN-LED |
| Brand | Z-Lite |
| Color | Silver (Brushed Nickel) |
| Material | Alloy Steel |
| Style | Harrison |
| Product Dimensions | 18"L x 4"W x 4.75"H |
| Item Weight | 2 Pounds |
| Power Source | Corded Electric |
| Light Source Type | LED (Integrated) |
| Wattage | 20 Watts |
| Voltage | 120 Volts |
| Indoor/Outdoor Usage | Indoor |
| Mounting Type | Ambient Lighting |
| UPC | 685659192728 |
Warranty Information
This Z-Lite product is covered by a manufacturer's warranty. Please refer to the warranty documentation included with your purchase or visit the official Z-Lite website for detailed terms and conditions regarding coverage, duration, and claims process. Retain your proof of purchase for warranty service.
Customer Support
For technical assistance, missing parts, or any questions regarding your Z-Lite Harrison Vanity Light, please contact Z-Lite customer support:
- Website: Visit the official Z-Lite website for support resources and contact information.
- Email/Phone: Refer to the contact details provided on the Z-Lite website or in your product packaging.
