Bewinner 433MHz 4-Key Remote Control Cloner

1. Introduction

This manual provides instructions for the Bewinner 433MHz 4-Key Remote Control Cloner, Model AK-K200803. This device is designed to copy common fixed and learning code remote controls operating at 433MHz, offering a convenient solution for controlling various systems such as garage doors, gates, and alarm systems. Please read this manual thoroughly before use to ensure proper operation and to maximize the product's lifespan.

2. Safety Information

• Keep the remote control away from water and high humidity.
• Do not expose the device to extreme temperatures or direct sunlight.
• Avoid dropping or subjecting the remote to strong impacts.
• Do not attempt to disassemble or modify the device, as this will void the warranty and may cause damage.
• Keep batteries out of reach of children. If swallowed, seek immediate medical attention.

3. Product Overview

The Bewinner 4-Key Remote Control Cloner is a compact and versatile device. It features four programmable buttons (A, B, C, D) for controlling different functions. The remote operates on a fixed frequency of 433MHz and is designed with advanced IC programming procedures to prevent accidental code deletion. Its lightweight design makes it easy to carry.

Image showing the front and back of the Bewinner 4-Key Remote Control Cloner. The front displays four circular buttons labeled A, B, C, and D. The back has a '433M' sticker, indicating its operating frequency.

Close-up view of the Bewinner 4-Key Remote Control Cloner, highlighting the four distinct buttons (A, B, C, D) and the sleek black and white design.

4. Specifications

5. Setup: Programming the Remote Control Cloner

The Bewinner 4-Key Remote Control Cloner allows you to duplicate signals from compatible 433MHz fixed and learning code remote controls. Follow these steps carefully for successful programming.

Image illustrating the remote control cloner in front of a house, emphasizing its function in copying fixed and learning codes at 433MHz. This highlights the advanced IC programming procedures designed to prevent accidental code deletion.

Step 1: Clear Existing Codes

1. Press and hold buttons A and B simultaneously on the cloner until the LED indicator flashes rapidly (approximately 3 seconds).
2. Release both buttons. The LED will flash briefly once to confirm that all pre-existing codes are cleared.

Step 2: Clone the Desired Button

1. Place your original remote control and the Bewinner cloner side-by-side, as close as possible (ideally touching).
2. Press and hold the button on your original remote that you wish to clone.
3. Simultaneously, press and hold the corresponding button (A, B, C, or D) on the Bewinner cloner where you want to store the code.
4. Hold both buttons until the LED indicator on the cloner flashes rapidly (this may take a few seconds). A rapid flash indicates successful cloning.
5. Release both buttons.

Step 3: Repeat for Other Buttons

• Repeat Step 2 for any other buttons (C and D) you wish to program.

Step 4: Test the Cloned Remote

• After programming, test the cloner with your device (e.g., garage door opener) to ensure it functions correctly.

Important Note on Compatibility:

This cloner is compatible with 433MHz fixed code and learning code remote controls. It is NOT compatible with rolling code (e.g., HCS200, HCS201, HCS300, HCS301) or encrypted remotes. Attempting to clone incompatible remotes will not be successful.

6. Operating Instructions

Once programmed, operate the Bewinner 4-Key Remote Control Cloner by simply pressing the corresponding button (A, B, C, or D) that you have assigned to a specific function. The remote offers a transmission distance of up to 50 meters, providing flexible control over your devices.

A hand holding the Bewinner 4-Key Remote Control Cloner, with a garage door opening in the background, demonstrating its practical use for controlling access systems.

The remote control cloner positioned in front of an open garage door with a car inside, illustrating its primary application for garage door operation.

The remote control cloner in front of a closed garage door, showing its readiness for use in securing or opening the garage.

7. Troubleshooting

• Remote not programming:
  • Ensure your original remote is compatible (fixed/learning code, 433MHz). Rolling code remotes are not supported.
  • Make sure the cloner's existing codes are cleared before attempting to program.
  • Place the original remote and the cloner as close as possible, ideally touching.
  • Try replacing the battery in the cloner if the LED does not light up or flashes weakly.
• Short operating distance:
  • Check the battery level of the cloner. A low battery can reduce transmission range.
  • Ensure there are no significant obstructions between the remote and the receiver.
• Accidental code deletion:
  • While the device has IC programming procedures to prevent accidental deletion, if codes are lost, simply re-program the remote following the setup steps in Section 5.

8. Maintenance

Battery Replacement:

The remote uses a 12V27A combined column battery. To replace the battery:

1. Carefully open the casing of the remote control. This may involve unscrewing small screws or gently prying the two halves apart.
2. Remove the old battery.
3. Insert a new 12V27A battery, ensuring correct polarity (+ and -).
4. Close the casing securely.

Cleaning:

Wipe the remote with a soft, dry cloth. Avoid using harsh chemicals, abrasive cleaners, or liquids, as these can damage the device's surface or internal components.

9. Warranty and Support

For any issues, questions, or technical support regarding your Bewinner 433MHz 4-Key Remote Control Cloner, please refer to the retailer's return policy or contact Bewinner customer support through their official channels. Please have your model number (AK-K200803) and purchase information ready when seeking assistance.