Avarro NX-TM2460 Medium Tilt Low-Profile Mount

1. Product Overview

The Avarro NX-TM2460 is a medium tilt, low-profile wall mount designed for displays ranging from 24 to 60 inches. It supports a maximum load capacity of 120 pounds and is compatible with VESA patterns from 75 x 75 mm to 400 x 400 mm. This mount features an open architecture wall plate, a secure locking mechanism, and height adjustability for easy leveling. It also offers up to 12 degrees of tilt to reduce glare, ensuring an optimal viewing experience.

Key Features:

• Supports 24" - 60" displays up to 120 lbs.
• VESA compatibility: 75 x 75 to 400 x 400 mm (W x H).
• Open architecture wall plate for easy cable access.
• Locking mechanism to secure display rails to the wall plate.
• Height adjustable for precise post-installation leveling.
• Tilts up to 12 degrees to minimize glare.
• Designed for simple installation and use.
• Includes a complete hardware kit.

Figure 1: Overview of the Avarro NX-TM2460 mount components.

2. Safety Information

Please read all instructions carefully before installation. If you have any questions, contact customer support. Improper installation can result in property damage or personal injury.

• Ensure the mounting surface can safely support the combined weight of the mount and the display.
• Do not exceed the maximum load capacity of 120 lbs (54.4 kg).
• Use appropriate tools and follow all installation steps precisely.
• Keep children away during installation.
• Verify all connections are secure before use.

3. Package Contents

Verify that all components are present and undamaged before proceeding with installation.

• Medium Tilt Mount (Wall Plate and Display Rails)
• Complete Hardware Kit (various screws, anchors, washers, spacers)

4. Setup and Installation

This section outlines the general steps for installing your Avarro NX-TM2460 mount. Specific wall types may require different anchors or tools not included.

1. Locate Mounting Position: Determine the desired height and center position for your display on the wall. Use a stud finder to locate wood studs if mounting on drywall, or ensure you have appropriate concrete/brick anchors.
2. Install Wall Plate: Position the wall plate at the marked location. Mark the drilling points through the wall plate holes. Drill pilot holes as required for your wall type. Secure the wall plate to the wall using the provided lag bolts and washers. Ensure the wall plate is level using a spirit level.
3. Attach Display Rails to TV: Carefully place your TV face down on a soft, clean surface. Identify the VESA mounting holes on the back of your TV. Select the appropriate screws, washers, and spacers from the hardware kit that fit your TV's VESA pattern. Attach the two display rails to the back of your TV, ensuring they are oriented correctly (hooks facing upwards and towards the wall plate).
4. Mount TV to Wall Plate: With assistance, carefully lift the TV and hook the display rails onto the top edge of the installed wall plate. Gently lower the TV until the rails are fully seated on the wall plate.
5. Secure Locking Mechanism: Locate the locking screws at the bottom of the display rails. Tighten these screws to secure the display rails to the wall plate, preventing accidental dislodgement.
6. Adjust Height and Tilt: The mount allows for post-installation height adjustment for leveling. Loosen the height adjustment screws on the display rails, adjust the TV to the desired level, and then re-tighten the screws. To tilt the display, loosen the tilt knobs on the side of the display rails, adjust to the desired angle (up to 12 degrees), and then re-tighten the knobs.

Figure 2: Example of the Avarro NX-TM2460 mount installed.

5. Operating Instructions

Once installed, the Avarro NX-TM2460 mount offers simple operation for adjusting your display's viewing angle.

• Tilting the Display: To adjust the vertical tilt angle, locate the tilt knobs on the sides of the display rails. Loosen these knobs, adjust the display to your preferred viewing angle (up to 12 degrees), and then firmly tighten the knobs to secure the position.
• Leveling the Display: If minor leveling adjustments are needed after initial installation, loosen the height adjustment screws on the display rails, carefully adjust the display's height, and then re-tighten the screws.

6. Maintenance

Regular maintenance ensures the longevity and safe operation of your mount.

• Cleaning: Wipe the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents that could damage the finish.
• Periodic Inspection: Periodically check all screws and bolts to ensure they remain tight and secure. Re-tighten if necessary.
• Weight Limit: Do not hang additional items or exceed the maximum weight capacity of 120 lbs (54.4 kg).

7. Troubleshooting

If you encounter issues with your Avarro NX-TM2460 mount, refer to the following common solutions:

• Display is not level: Ensure the wall plate was installed level. Use the post-installation height adjustment feature on the display rails to fine-tune the level.
• Display is not secure: Verify that the locking screws at the bottom of the display rails are fully tightened. Check that all wall plate mounting bolts are secure.
• Difficulty tilting: Ensure the tilt knobs on the display rails are sufficiently loosened before attempting to adjust the tilt. Re-tighten them firmly after adjustment.
• Missing parts: If any parts are missing from the package, contact customer support immediately.

8. Specifications

9. Warranty Information

This product is covered by a limited warranty against defects in materials and workmanship. Please refer to the warranty card included in your package or visit the manufacturer's website for full details regarding warranty terms, conditions, and duration. Keep your proof of purchase for warranty claims.

10. Customer Support

For technical assistance, missing parts, or warranty inquiries, please contact Avarro customer support. Refer to the contact information provided in your product packaging or on the official Avarro website.