Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your GAMDIAS AURA GC2 E WH A ATX Mid Tower PC Case. Please read this manual thoroughly before beginning installation to ensure proper setup and optimal performance.
Image: Front-left view of the GAMDIAS AURA GC2 E WH A ATX Mid Tower PC Case, showcasing the perforated front panel with ARGB fans and the tempered glass side panel.
Setup and Installation
Follow these steps to properly set up your GAMDIAS AURA GC2 E WH A PC case and install components.
1. Preparing the Case
- Unpack the PC case and remove all packaging materials.
- Place the case on a stable, flat surface.
- Remove the tempered glass side panel by unscrewing the thumb screws, typically located at the rear of the panel. Carefully lift and set aside the panel on a soft, non-abrasive surface to prevent scratches.
- Access the interior for component installation.
Image: Illustration showing the removal of the tempered glass side panel for tool-free access to the case interior.
2. Motherboard Installation
- Ensure the correct standoffs are installed for your motherboard form factor (ATX, Micro-ATX, Mini-ITX).
- Carefully align your motherboard with the standoffs and the I/O shield opening at the rear of the case.
- Secure the motherboard with screws.
3. Power Supply Unit (PSU) Installation
- Install the PSU into the dedicated shroud area at the bottom of the case.
- Secure the PSU with screws from the rear of the case.
- Route necessary cables through the cable management cutouts.
4. Storage Drive Installation
- The case supports 2 x 3.5" drives (or 1 x 2.5" + 1 x 3.5" in the HDD cage) and 2 x 2.5" drives on dedicated trays.
- Mount your SSDs/HDDs into the appropriate bays or trays and secure them.
5. Graphics Processing Unit (GPU) Installation
- Remove the necessary PCIe slot covers at the rear of the case.
- Insert your GPU into the PCIe slot on the motherboard and secure it with a screw.
- The case supports GPUs up to 340mm in length.
Image: Diagram illustrating the compact mid-tower case dimensions (195mm width, 395mm depth, 450mm height) and GPU length support up to 340mm, along with the PSU shroud design.
Image: Visual representation of component clearance limits: CPU Cooler up to 160mm, GPU up to 340mm, and PSU up to 160mm.
6. Cooling System Configuration
- The case comes with four pre-installed 120mm ARGB fans.
- Additional fan support: The case supports up to six 120mm fans.
- Radiator support: A 360mm AIO/radiator can be installed in the front.
- Ensure all fan cables are connected to the appropriate headers on your motherboard or the included fan controller.
Image: Diagram detailing cooling support: 2x 120mm fans at the top, 1x 120mm fan at the rear, and 3x 120mm or 2x 140mm fans or a 360mm radiator at the front.
Image: Close-up view of the chamfered white perforated front panel, highlighting the pre-installed ARGB fans designed for superior air intake.
7. Front I/O Panel Connections
- Connect the front panel cables (USB 3.0, USB 2.0, HD Audio, Power Switch, Reset Switch, LED Control) to the corresponding headers on your motherboard.
Image: Detail of the top-front I/O panel, featuring 2x USB 2.0 ports, 1x USB 3.0 port, a reset button, and HD audio connectivity.
8. Cable Management
- Utilize the space behind the motherboard tray and the PSU shroud to route and tie down cables for a clean build and improved airflow.
9. Final Assembly
- Once all components are installed and cables are managed, reattach the tempered glass side panel.
- Ensure all screws are tightened securely.
Operating Instructions
After successful assembly, your GAMDIAS AURA GC2 E WH A PC case is ready for operation.
- Power On: Press the power button located on the top I/O panel to start your computer.
- ARGB Fan Control: The pre-installed ARGB fans can be controlled via the dedicated LED control button on the top I/O panel, or through compatible motherboard software if connected to an ARGB header. Note that the fans are fixed RGB and may not be controllable via standard 4-pin RGB headers.
- USB Ports: Use the USB 3.0 and USB 2.0 ports on the top panel for connecting peripherals and external devices.
- Audio Jacks: Connect your headphones and microphone to the HD Audio jacks on the top panel.
Maintenance
Regular maintenance helps ensure optimal performance and longevity of your PC case.
- Dust Cleaning: Periodically clean dust from the perforated front panel and any other intake areas. A soft brush or compressed air can be used.
- Interior Cleaning: With the system powered off and unplugged, carefully remove the side panel and use compressed air to clean dust from internal components and fans.
- Tempered Glass: Clean the tempered glass panel with a soft, lint-free cloth and a non-abrasive glass cleaner. Avoid harsh chemicals.
Troubleshooting
If you encounter issues with your PC case, refer to the following common troubleshooting tips:
- Fans Not Spinning:
- Check if the fan power cables are securely connected to the PSU (SATA power) or motherboard headers.
- Ensure the fan controller (if applicable) is receiving power.
- ARGB Lights Not Working/Incorrect Color:
- Verify that the ARGB cables are correctly connected to the motherboard's ARGB header or the case's LED control button.
- Use the LED control button on the top I/O panel to cycle through lighting modes.
- If connected to a motherboard, ensure the motherboard's RGB software is installed and configured correctly.
- Front USB Ports Not Functioning:
- Confirm that the USB 3.0 and USB 2.0 headers from the case are properly connected to the corresponding headers on your motherboard.
- Front Audio Jacks Not Functioning:
- Ensure the HD Audio cable from the case is correctly plugged into the audio header on your motherboard.
- Check your operating system's audio settings and drivers.
Specifications
Detailed specifications for the GAMDIAS AURA GC2 E WH A ATX Mid Tower PC Case:
| Feature | Detail |
|---|---|
| Model Name | AURA GC2 E WH A |
| Case Type | Mid Tower |
| Motherboard Compatibility | ATX, Micro-ATX, Mini-ITX |
| Dimensions (LxWxH) | 15.55 x 7.67 x 17.71 inches (395 x 195 x 450 mm) |
| Item Weight | 10.8 pounds |
| Material | Acrylonitrile Butadiene Styrene (ABS), Metal, Plastic, Tempered Glass |
| Color | White |
| Pre-installed Fans | 4x 120mm ARGB Fans |
| Max Fan Support | Up to 6x 120mm Fans |
| Radiator Support | Front: Up to 360mm AIO/Radiator |
| Max GPU Length | 340mm |
| Max CPU Cooler Height | 160mm |
| Max PSU Length | 160mm |
| Drive Bays | 2 x 3.5" (or 1 x 2.5" + 1 x 3.5" in HDD Cage) / 2 x 2.5" HDD Tray |
| Expansion Slots | 7 |
| Front I/O Ports | 1x USB 3.0, 2x USB 2.0, 1x HD Audio, 1x LED Control Button |
| Cooling Method | Air |
| Power Supply Mounting Type | Bottom Mount |
Warranty Information
Specific warranty details for the GAMDIAS AURA GC2 E WH A PC Case are typically provided with the product packaging or on the official GAMDIAS website. Please refer to those resources for the most accurate and up-to-date warranty terms and conditions.
Customer Support
For technical assistance, troubleshooting beyond this manual, or inquiries regarding your GAMDIAS AURA GC2 E WH A PC Case, please visit the official GAMDIAS website or contact their customer support channels. Contact information is usually available on the product packaging or the company's website.
You can visit the GAMDIAS Store on Amazon for more information: GAMDIAS Store
