Primevolve SH09 Electric Heater with Humidifier Function User Manual

Introduction

Thank you for purchasing the Primevolve SH09 Electric Heater with Humidifier Function. This ceramic heater is designed to provide efficient and comfortable heating for indoor spaces, featuring rapid heating, a built-in humidifier, quiet operation, and energy-saving modes. Please read this manual thoroughly before use to ensure safe and optimal performance.

Important Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all instructions before using this heater.
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 1 meter (3 feet) from the front of the heater and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
• Always unplug heater when not in use.
• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
• Do not use outdoors.
• This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
• To disconnect heater, turn controls to OFF, then remove plug from outlet.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
• This heater is equipped with a tip-over safety switch and overheat protection. If the heater tips over or overheats, it will automatically shut off.
• The product is made with V0 flame-retardant materials.

Image: This image illustrates the safety features of the Primevolve SH09 heater, including V0 flame-retardant materials, an improved safety plug, overheat protection, and anti-tip protection. It shows a child and a cat near the heater, emphasizing its safe design.

Product Overview

The Primevolve SH09 is a versatile ceramic heater designed for optimal comfort. Key features include:

• Rapid Heating: 2000W ceramic heating element provides warmth in 2 seconds.
• Humidifier Function: Integrated humidifier with a 280ml water tank, releasing 30-40 ml/hour.
• Quiet Operation: Operates at a low noise level of 37.5 dB.
• ECO Mode: Intelligent energy-saving mode adjusts power based on ambient temperature.
• 70° Oscillation: Wide-angle oscillation for even heat distribution.
• Safety Features: V0 flame-retardant materials, tip-over protection, overheat protection, and 24-hour auto-off.

Image: This image highlights the rapid heating capability of the Primevolve SH09 heater, showing heat emanating from the unit and indicating "2S Rapid Heating" and "2000W Ceramic PTC" for areas up to "25 M²".

Image: This image demonstrates the 3-in-1 functions of the Primevolve SH09 heater. It shows a person working in a room with the heater and illustrates three modes: 1) Hot air/natural air, 2) Hot air + humidification, and 3) Hot air + humidification + flame effect.

Setup

1. Unpacking: Carefully remove the heater from its packaging. Retain packaging for storage if needed.
2. Placement: Place the heater on a firm, level surface. Ensure there is at least 1 meter (3 feet) of clear space around the heater from walls, furniture, and other objects to allow for proper airflow and prevent fire hazards. The heater is recommended for areas up to 25 square meters.
3. Power Connection: Plug the heater directly into a 220-240V AC, 50Hz wall outlet. Do not use extension cords or power strips.
4. Filling the Water Tank (for Humidifier Function):
   • Locate the water tank on the heater (refer to product diagram if available).
   • Carefully remove the water tank.
   • Fill the tank with clean, distilled water. Do not overfill. The tank capacity is 280ml.
   • Securely replace the water tank into its position.

Operating Instructions

The heater can be operated using the control panel on the unit or the included remote control.

Control Panel / Remote Control Functions:

• Power Button (⏻): Press to turn the heater ON or OFF.
• Mode Button (M): Cycle through heating modes:
  • High Heat (2000W): Maximum heating power.
  • Low Heat (1450W): Reduced heating power.
  • Fan Only (8W): Circulates air without heat.
  • ECO Mode: Automatically adjusts power (between 2000W and 1450W) to maintain a set temperature, optimizing energy consumption.
• Temperature Adjustment (+ / -): Adjust the desired room temperature when in heating modes.
• Oscillation Button (↻): Activates or deactivates the 70° oscillation function for wider heat distribution.
• Timer Button (⏱): Set the auto-off timer. Press repeatedly to select desired operating duration (e.g., 1-12 hours).
• Humidifier Button (💧): Turns the humidifier function ON or OFF.
• Flame Effect Button (🔥): Activates or deactivates the decorative flame effect.

Image: This image illustrates the 70-degree oscillation feature of the Primevolve SH09 heater, showing heat spreading across a wider area in a room. A remote control is also visible, indicating remote operation capability.

Image: This image explains the ECO mode of the Primevolve SH09 heater, demonstrating how it saves energy by adjusting power consumption. A graph shows a comparison of energy usage between the Primevolve heater and other heaters, highlighting a 40% energy saving.

Maintenance

Regular maintenance ensures the longevity and efficient operation of your heater.

1. Cleaning the Exterior:
   • Always unplug the heater and allow it to cool completely before cleaning.
   • Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
   • Ensure no water enters the interior of the heater.
2. Cleaning the Air Inlet/Outlet:
   • Use a vacuum cleaner with a brush attachment to gently remove dust and lint from the air inlet and outlet grilles.
   • Do not attempt to disassemble the heater for cleaning.
3. Cleaning the Water Tank (for Humidifier):
   • Empty and rinse the water tank regularly, especially if the humidifier function is used frequently.
   • To prevent mineral buildup, clean the tank with a mild descaling solution (e.g., vinegar and water) periodically. Rinse thoroughly before refilling.
4. Storage:
   • When not in use, store the heater in a cool, dry place, preferably in its original packaging.
   • Wrap the power cord neatly to prevent damage.

Troubleshooting

Image: This image highlights the quiet operation of the Primevolve SH09 heater, showing a sleeping child in a bedroom with the heater operating at a low noise level of 37.5 dB, indicating a peaceful environment.

Specifications

• Model: SH09
• Brand: Primevolve
• Type: Ceramic Electric Heater with Humidifier
• Power Output: 2000W (High), 1450W (Low), 8W (Fan Only)
• Voltage: 220-240V AC, 50Hz
• Special Features: Energy Saving (ECO Mode), Adjustable Heat Output, 70-degree Oscillation, Humidifier Function, Flame Effect
• Color: White
• Form Factor: Tower
• Recommended Area: Up to 25 m²
• Noise Level: 37.5 dB
• Water Tank Capacity: 280 ml
• Humidification Rate: 30-40 ml/hour
• Safety: V0 Flame-retardant materials, Tip-over Protection, Overheat Protection, 24-hour Auto-off
• Power Cord Length: 1.5 meters

Warranty and Support

Primevolve products are manufactured to the highest quality standards. For warranty information, technical support, or customer service inquiries, please refer to the contact information provided with your purchase or visit the official Primevolve website. Please have your model number (SH09) and purchase details ready when contacting support.