1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Okinos RGB Fans. These 120mm Air Series fans feature 4-Pin PWM for precise speed control and 3-Pin Addressable RGB for customizable lighting effects, including an ARGB controller hub and remote. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of your product.
Image: The Okinos RGB Fans 5-pack, showcasing the fans, controller hub, and remote control.
2. Package Contents
Verify that all components listed below are present in your package:
- (1) Okinos Air Series 120mm Addressable RGB Fan x 5
- (2) Fans Hub x 1
- (3) Remote Controller x 1
- (4) Screws x 20
3. Installation Guide
3.1 Fan Mounting
Mount the Okinos RGB fans into your PC case using the provided screws. Each fan features 8 rubber anti-vibration pads to minimize noise and vibration during operation.
Image: Close-up of an Okinos fan highlighting the 8 rubber anti-vibration pads for noise reduction.
Modding Tip: When installing the fans, it is suggested to use a PH2 Cross Head Screwdriver. The fan screws are self-tapping, meaning they create threads inside the fan's mounting holes during installation. Using the correct screwdriver will prevent damage to the screw surface and ensure a successful installation.
Image: Diagram illustrating the use of a PH2 Cross Head Screwdriver for fan installation and a warning against connecting PWM fans to PUMP headers.
3.2 Connecting to the Control Hub
Connect all Okinos RGB fans to the included Fans Hub. The hub centralizes power and RGB control for all connected fans.
Image: A detailed diagram illustrating how to connect the ARGB PWM fans to the Okinos control hub, and then connect the hub to the motherboard and power supply. It highlights connecting the "Red" PWM port to read speed via BIOS.
3.3 Power and Motherboard Connections
The Okinos fans utilize both 4-Pin PWM and 3-Pin Addressable RGB connectors. Ensure proper connection for full functionality.
- 4-Pin PWM Connector: Connect the 4-Pin PWM cable from the fan hub to a 4-Pin PWM fan header on your motherboard. This allows the motherboard to control fan speed based on system temperature. The fans operate at 1600±10% RPM, providing a maximum airflow of 35.49 CFM.
- 3-Pin Addressable RGB Connector: Connect the 3-Pin Addressable RGB cable from the fan hub to a 3-Pin 5V Addressable RGB header on your motherboard. This enables synchronization of the fan's RGB lighting with your motherboard's software.
Important: The Okinos A12 fans CANNOT be used with a 4-Pin 12V RGB connector. Ensure you connect to a 3-Pin 5V Addressable RGB header to prevent damage.
Image: A close-up diagram illustrating the correct connection of the A12 fan's 3-Pin 5V Addressable RGB connector to a compatible motherboard header, with a clear warning against using a 4-Pin 12V RGB connector.
PWM Functionality: To enable the PWM function, the PWM fan must be plugged into the "PWM" connector on the motherboard, whether it's through the PWM controller, a 1-to-3 splitter cable, the extension cable, or the PWM connector of the fan itself. Do NOT connect it to a PUMP header, as this will cause the fan to run at full speed constantly.
4. Operating Instructions
4.1 RGB Lighting Control
The Okinos RGB fans offer versatile lighting control options:
- Motherboard Control: Sync the fan's RGB lighting with your motherboard's software. Press and hold the "Mode" button on the remote or hub for 3 seconds to initiate synchronization when connecting with the system start. Automatic synchronization occurs upon reopening if the system is turned off.
- Fan Controller: Use the included fan hub for direct control of lighting effects.
- Remote Control: The included manual remote controller allows you to select from 64 built-in lighting options and adjust the fan's speed. To disconnect M/B sync and switch to remote controller, lightly press the MODE button once.
Image: The included manual remote controller with various buttons for lighting modes and fan speed, alongside a close-up of the control hub buttons.
Image: A comparison table showing the compatibility of Okinos A12 ARGB fans with Motherboard Control, Fan Controller, and Remote Control, indicating full compatibility.
4.2 Fan Performance and Noise
The Okinos RGB fans are designed for high performance with minimal noise. They feature 8 ARGB LEDs and 9 transparent fan blades, capable of displaying 16.8 million colors for personalized lighting effects.
Image: An illustration highlighting the individual 8 ARGB LEDs on the fan, capable of producing 16.8 million colors.
The impeller design focuses on minimizing noise level to 26.9 dBA while delivering superior airflow (35.49 CFM) and pressure (1.17 mmH2O). With hydraulic bearings, friction and vibration are minimized, ensuring quiet operation even at maximum speed (1600 RPM).
Image: A visual representation emphasizing the low noise level of 26.9 dBA for the Okinos silent case fan.
Image: An illustration demonstrating the fan's adjustable speed up to 1600 RPM via 4-Pin PWM, maintaining low noise levels.
Image: A diagram illustrating the high airflow (35.49 CFM) and air pressure (1.17 mmH2O) performance of the 120mm fan at 1600 RPM.
5. Maintenance
To ensure optimal performance and longevity of your Okinos RGB Fans, regular maintenance is recommended:
- Cleaning: Periodically clean the fan blades and housing to prevent dust buildup, which can impede airflow and increase noise. Use compressed air or a soft, dry cloth. Ensure the system is powered off before cleaning.
- Cable Management: Ensure all cables are neatly managed and not obstructing airflow or fan blades.
- Inspection: Regularly inspect fan blades for any damage or obstructions.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fans not spinning | No power to hub/fans; Incorrect connection; Faulty fan/hub. | Check power supply connection to hub. Ensure all fan cables are securely connected to the hub. Verify hub is connected to motherboard/power. |
| RGB lights not working | Incorrect ARGB connection (e.g., 12V header); Loose ARGB cable; Software issue. | Ensure 3-Pin 5V ARGB connection. Reconnect ARGB cables. Check motherboard RGB software settings. Try remote control. |
| Fans running at full speed constantly | PWM cable connected to PUMP header; PWM not enabled in BIOS. | Relocate PWM cable to a standard 4-Pin PWM fan header. Check BIOS settings for fan control. |
| Excessive noise/vibration | Loose mounting screws; Obstruction; Dust buildup. | Tighten mounting screws. Clear any obstructions. Clean fan blades. |
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | OKICF-A12ABT4P-1225X5 |
| Product Dimensions | 4.72 x 0.98 x 4.72 inches (120mm x 25mm x 120mm) |
| Weight | 1.87 Pounds (for 5-pack) |
| Brand | Okinos |
| Power Connector Type | 3-pin ARGB, 4-pin PWM |
| Voltage | 12 Volts (DC) |
| Cooling Method | Air |
| Compatible Devices | Desktop PCs |
| Noise Level | 26.9 dB(A) |
| Material | Copper (likely referring to internal components/bearings) |
| Maximum Rotational Speed | 1600 ± 10% RPM |
| Air Flow Capacity | 35.49 CFM (Max.) |
| Static Pressure | 1.17 mmH2O (Max.) |
| LEDs | 8 Addressable RGB LEDs per fan |
| Lifespan | 70,000 hours @ 25°C |
8. Warranty and Support
Okinos products are manufactured to high quality standards. For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official Okinos website. Keep your proof of purchase for warranty claims.
For further assistance, please contact Okinos customer support.