1. Introduction
This manual provides essential information for the setup, operation, and maintenance of your METRONIC 441680 Fransat 4K UHD HDR10 Satellite Decoder. Please read this manual carefully before using the device to ensure proper functionality and to maximize your viewing experience.
The METRONIC 441680 decoder offers an exceptional visual and audio experience with 4K UHD-HDR10 technology and Dolby Digital Atmos sound. It allows you to receive free TNT channels in High Resolution up to UHD via satellite, without a subscription. A Fransat card is included for immediate optimal reception.
2. What's in the Box
Upon opening the package, verify that all the following items are present:
- METRONIC 441680 Fransat 4K UHD HDR10 Satellite Decoder
- Fransat UHD Access Card
- Remote Control
- Power Cable
Figure 2.1: Contents of the METRONIC 441680 package, including the decoder, remote, and power supply.
Video 2.1: An unboxing video demonstrating the contents of the package and initial handling of the decoder and accessories.
3. Setup and Installation
Follow these steps to set up your METRONIC 441680 decoder:
- Connect the Power Cable: Plug the power cable into the decoder's power input and then into a wall outlet.
- Connect to TV (HDMI): Use an HDMI cable to connect the decoder's HDMI output to an available HDMI input on your television.
Figure 3.1: Rear panel connections of the decoder, highlighting the HDMI port for TV connection.
- Connect Satellite Antenna: Connect your satellite dish cable to the "ENTREE LNB" (LNB Input) port on the back of the decoder.
- Insert Fransat Card: Carefully insert the Fransat UHD Access Card into the designated slot on the decoder. Ensure it is inserted correctly as indicated by the device.
- Insert Remote Control Batteries: Open the battery compartment on the back of the remote control and insert two AAA batteries (not always included).
- Power On: Turn on your television and the METRONIC 441680 decoder.
- Select TV Input: On your TV, select the correct HDMI input source corresponding to where the decoder is connected.
Video 3.1: A demonstration of connecting the decoder to a TV via HDMI and selecting the correct input source.
- Initial Channel Scan: Follow the on-screen instructions to perform an automatic channel scan. This will detect and store all available Fransat channels.
4. Operating Instructions
4.1 Basic Functions
- Power On/Off: Use the power button on the remote control or the front panel.
- Channel Navigation: Use the CH+/- buttons to change channels.
- Volume Control: Use the VOL+/- buttons to adjust the volume.
- Menu Access: Press the MENU button to access the main menu for settings and features.
4.2 Advanced Features
- Time Shift (Pause and Play TV): Connect a USB storage device (USB key or external hard drive) to the USB Double Power port. Press the PAUSE button during live TV to pause, and PLAY to resume.
- Multimedia Playback: Insert a USB storage device containing multimedia files (photos, music, videos) into the USB port. Navigate to the multimedia section in the main menu to browse and play your content.
- Parental Control: Access the parental control settings via the main menu to manage access to certain channels or programs.
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the decoder. Do not use liquid cleaners or abrasive materials.
- Ventilation: Ensure the decoder has adequate ventilation. Do not block the ventilation slots.
- Software Updates: Periodically check for software updates through the decoder's menu settings to ensure optimal performance and access to the latest features.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No picture/sound | Incorrect TV input selected, loose HDMI cable, decoder not powered on. | Ensure TV is on the correct HDMI input. Check HDMI cable connections. Verify decoder is powered on. |
| No channels found | Antenna not connected, incorrect satellite settings, no channel scan performed. | Check satellite antenna connection. Perform an automatic channel scan from the menu. Ensure Fransat card is correctly inserted. |
| Remote control not working | Dead batteries, obstructed sensor, remote not paired (if applicable). | Replace batteries. Ensure no obstructions between remote and decoder. Refer to the full manual for remote pairing instructions if needed. |
| Time Shift/USB playback not working | USB device not recognized, incompatible file format, insufficient storage. | Ensure USB device is properly formatted (FAT32/NTFS). Check file compatibility. Ensure sufficient free space on the USB device. |
7. Specifications
| Brand | Metronic |
| Model | 441680 |
| Display Technology | 4K UHD HDR10 |
| Audio Formats | Dolby Digital Atmos (AC4), Dolby Digital Plus (E-AC-3), MPEG-1 Audio Layer 2 |
| Video Formats | MPEG-2 / MPEG-4 / HEVC |
| USB Port | Double Power (1 port) |
| HDMI Ports | 1 |
| Functions | Pause and Play TV (Time Shift), Multimedia playback via USB |
| Compatibility | Compatible with all UHD TVs |
| Dimensions (L x W x H) | 13 x 17 x 3.5 cm |
| Weight | 600 grams |
| Color | Black |
| Voltage | 220 Volts |
Figure 7.1: Physical dimensions of the METRONIC 441680 decoder.
8. Warranty Information
The METRONIC 441680 Satellite Decoder comes with a 2-year manufacturer's warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For specific terms and conditions, refer to the warranty card included in your package or contact Metronic customer support.
9. Customer Support
For further assistance, technical support, or service inquiries, please visit the official Metronic website or contact their customer service department. Contact details can typically be found on the product packaging or the manufacturer's website.
You can also visit the Metronic Store on Amazon for additional product information and resources.
